← All sections of PWD Maharashtra SSR 2022-23
| Code | Description | Unit | Rate |
|---|---|---|---|
| 51.01 | Providing & Fixing in position, Acoustical Panelling made from Fabric wrapped Compressed polyester fibre nonwoven 9 mm panels on, 50 x 50 mm sal-wood frame of 600 x 600 c to c having wooden supports from wall of required length, in front of 1000 gsm synthetic wool 50 mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing-items / paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete | sqm | ₹ 4,590 |
| 51.02 | Providing & Fixing in position, Acoustical Panelling made from Wood-wool board 20mm on,50 x50mmSal-woodframeof600x600ctochaving woodensupports fromwall of required length, in front of 1000 Gsm synthetic wool 50 mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing-items / paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects. including all materials labour,finishing etc complete | sqm | ₹ 3,430 |
| 51.03 | Providing & Fixing in position, Acoustical Panelling made from Gypsum plain 12mm panels on, 50 x 50 mm Sal-wood frame of 600 x 600 c to c having wooden supports from wall of required length, in front of 1000 Gsm synthetic wool 50 mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing- items / paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects. including all materials labour,finishing etc complete | sqm | ₹ 2,300 |
| 51.04 | Providing & Fixing in position, Acoustical Panelling made from 12mm wp Ply wood & 1.5mm laminate on, 50 x 50 mm Sal-wood frame of 600 x 600 c to c having wooden supports from wall of required length, in front of 1000 Gsm synthetic wool 50 mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing-items / paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete | sqm | ₹ 5,090 |
| 51.05 | Providing & Fixing in position Acoustical Doors along with 150 x 150 mm teak wood frame, doors made from 50mm Teak wood frame 600 x600 c to c filled with 1000 Gsm synthetic wool 50mm thick and 3mm Tecsound from both sides, 12mm waterproof ply & veneer from both sides, including 150mm heavydutySS hinges (Geze / Dorma or eq.) 4 no each leaf, with Door-closer (Dorma / Geze or eq.) including cost of required Cut- Outs, decorative mouldings / finishing-items / melamine polish & Scaffolding as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete | sqm | ₹ 23,700 |
| 51.06 | Providing & fixing in position Stage flooring Made from 18mm plywood 1200 x 2400 & 18mm Teakwood planks 100 x 800 having tongue & grove on Sal-wood frame of 50 x 100 at 600mm c to c on stage surface including cost of required Cut-Outs, decorative mouldings / finishing-items / polish etc., as per Architectural & Acoustical Design & Instructions & Complete in all aspects..including all materials labour,finishing etc complete | sqm | ₹ 8,215 |
| 51.07 | Providing & Fixing in position, Acoustical Ceiling made from Gypsum Plain Panels on approved heavy duty G.I. frame ceiling channels at 450 c to c, & intermediate channels not more than 1200 c to c, along with ply wood forms suspended with Hangers from Roof, in front of 1000 Gsm synthetic wool 50 mm thick, with Paint, including cost of required Cut-Outs, decorative mouldings / finishing-items & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete | sqm | ₹ 1,465 |
| 51.08 | Providing & Fixing in position, AcousticalCeiling madefrom Compressed polyester fibre nonwoven 9mm panels on approved heavyduty GI frame 300 mm c to c & intermediate channels at 1200 mm c to c, suspended with Hangers from Roof, including cost of required Cut-Outs, decorative mouldings / finishing-items & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour,finishing etc complete | sqm | ₹ 2,865 |
| 51.09 | Providing & Fixing in position, Acoustical Ceiling made from Rigitone 8/18 perforated panels on approved heavy duty G.I. frame, ceiling channels at 300 c to c, & intermediate channels not more than 1200 c to c, suspended with Hangers from Roof, in front of 1000 Gsm synthetic wool 50 mm thick, with Paint, including cost of required Cut-Outs, decorative mouldings / finishing-items & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour,finishing etc complete | sqm | ₹ 4,135 |
| 51.10 | Providing & Fixing in position, Acoustical Panelling made from 12mm thick Agro wood strips of 50, 75 7 100 mm width on 50 x 50 mm Sal-wood frame of 600 x 600 c to c having supports from wall of required length, in front of 1000 gsm synthetic wool 50 mm thick withapprovedcolouredfabriconstrips side& chicken meshon wallside, including cost of required Cut-Outs, decorative mouldings / finishing-items / Melamine Polish & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects. including all materials labour,finishing etc complete | sqm | ₹ 5,075 |
| 51.11 | Providing & Fixing in position, Fabric wrapped Compressed polyester fibre nonwoven 9mm panels above the wood wool board panelling or existing sal wood frame, using adhesive, as per Architectural & Acoustical Design & Instructions & Complete in all aspects. including all materials labour,finishing etc complete | sqm | ₹ 2,950 |
| 51.12 | Providing & Fixing in position, Partition made from 12mm thick Gypsum from both sides on 50 x 50 mm Sal-wood frame of 600 x 600 c to c, having of 800 gsm synthetic wool 50 mm thick in between, including cost of required Cut-Outs & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour,finishing etc complete | sqm | ₹ 2,524 |
| 51.13 | Providing & Fixing in position, Carpet more than 800+ gsm, made with100% stain proof fibres of approved make along with 5mm underlay as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour,finishing etc complete | sqm | ₹ 1,450 |
| 51.14 | Providing & Fixing in position, 1000 mm wide Auto-glow Aluminium extruded strips on auditorium steps as per Design & Instructions & Complete in all aspects. Make Piccolo or Nexus | nos | ₹ 1,410 |
| 51.15 | Providing & Fixing in position, 12mm wp Plywood & 1.5mm laminate panels above the fabricated frame on one side, as per Architectural & Acoustical Design & Instructions & Complete in all aspects. including all materials labour,finishing etc complete | sqm | ₹ 3,170 |
| 51.16 | Providing & Fixing in position, MS fabrication work using angles, sqr tubes, c channels etc for various partition frame as per Design & Instructions & Complete in all aspects. including all materials labour,finishing etc complete | kg | ₹ 85 |
| 51.17 | Providing & Fixing in position, Under Deck insulation for metal deck using 1000 Gsm synthetic wool with fixed to deck using adhesive and chicken mesh. | sqm | ₹ 740 |
| 51.18 | Providing & fixing in position, heavydutyfullyupholstered Auditorium chairs 520 mm c to c tip-up type. Height of back should be less than 1030 mm with plastic protective cover on back and bottom having teak wood handles. Back to back distance is 1000mm. The auditorium chairs should be of following specifications 1. Powder Coated Heavy duty MS Stand. 2. Individually moulded, ergonomically designed seat and back cushions. 3.Moulded Polyurethane Foam cushion. PU foam density 48 – 52 Kilograms/cu.mtr 4. Moulded Polyurethane Foam manufactured in certified ISO 9001 facility to ensure consistency in density for longevity.5.Upholstered in Foam laminated stretch sandwich Fabric for clean finish and soft comfortable feel as per the colour & pattern selected by the client. 6.Seat and Back should have moulded synthetic protective cover. 7. Wooden or PU armrest 65mm x 20mm - 330mm long. 8.Mounted using Anchor fasteners. | nos | ₹ 6,000 |
| 51.19 | Providing and Fixing Rollar Blinds AMI Make or approved make & shade of 38mm round Aluminium channel with Blackout fabric & telting with chain (Ball) system with all necessary fixtures and fitting etc. complete. (Sample to be final by Engineer In-charge prior execution of work) | sqm | ₹ 2,152 |
| 51.20 | Providing and Fixing Vertical Blinds of approved Make and shade of 100mm regular fabric with powder coated aluminium channel with telting PVC chain & bottom weight plate with all necessary fixtures and fitting etc. complete. (Sample to be final by Engineer In-charge prior execution of work) | sqm | ₹ 1,025 |
| 51.21 | Executive's Table @ 1800Lx900Dx750HT Providing & Fixing of Table @ 1800Lx900Dx750HT - TOP & GABLE END to be made of Membrane finish with soft water fall edges & curved panel & Decorated Anodized section MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band as per drawing | nos | ₹ 17,231 |
| 51.22 | Pedestal Unit @ 420Lx450Dx650HT Providing & Fixing of PEDESTAL @ 420Lx450Dx650HT:- To be made out of Complete Membrane consist of three Drawers as per drawing. | nos | ₹ 9,004 |
| 51.23 | Credestal @ 1200Lx450Lx650HT Providing & Fixing of LOW HEIGHT CREDESTAL@ 1200LX 450D X650H:-To be made out of Membrane Finish ( 2 Openable Shutter & 3 Drawer Pedestal in between)as per drawing. | nos | ₹ 17,498 |
| 51.24 | Executive Table @ 2250Lx2100Dx750HT including Low Height Credestal @ 1200Lx450Dx650HT Providing & Fixing of Table @ 2250Lx2100Dx750HT TOP & GABLE END to be made of Membrane finish with soft water fall edges & curved panel & Decorated Anodized section MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band. INCLUDING CREDESTAL @ 1200L X450DX650H:-Tobemadeout ofMembraneFinish (2OpenableShutter &3 Drawer Pedestal in between) as per drawing. | nos | ₹ 42,635 |
| 51.25 | Medium Height Partition @ 1800/1200HT TILE BASED PARTITION SYSTEM:- Tile based Aluminum partition system of 1800/1200 mm ht. made of 60mm thk aluminum frames having two separate race ways for laying electrical & computer wiring. The wire management shall be through to the race wayto befitted at bottom ofpartition andother immediatelybelow ofwork topwith hook on type raceway cover for easy access of wires. Frames to be joined by aluminum connectors with M6 x 16 pan-head machin screw and washer with aluminum post cover. Post cover of snap on fashion to be connected on aluminum connectors. All visible aluminium to be in anodized finish. The top/ exposed sides of the frame and posts should be covered with horizontal/ Vertical trim and caps made of Aluminum in anodized finish in order to enhance its look.Upper tiles of partition to be in Soft Board or Marker tile of 9mm. thk., and prelaminated partical board lower tiles in laminate finish of 9mm. thk. on both the sides. | rmt | ₹ 7,552 |
| 51.26 | Free Standing Table @ 1500Lx600Dx750HT Providing and fixing Table of Size 1500 x 600 x 750 mm. Top: made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Legs: C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel: Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY):- Metal Powder Coated - Black Color, CPU TROLLEY:- Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board, | nos | ₹ 16,893 |
| 51.27 | Free Standing Table @ 1350Lx600Dx750HT Providing and fixing Table of Size 1350 x 600 x 750 mm. Top: made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Legs: C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel: Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY):- Metal Powder Coated - Black Color, CPU TROLLEY:- Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board, | nos | ₹ 16,411 |
| 51.28 | Free Standing Table @ 1200Lx600Dx750HT Providing and fixing Table of Size 1200 x 600 x 750 mm. Top: made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Legs: C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel: Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY):- Metal Powder Coated - Black Color, CPU TROLLEY:- Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board, | nos | ₹ 14,436 |
| 51.29 | Library Area Table @ 1350Lx750Dx750HT Providing & Fixing of FREE STANDING TABLE @ 1350Lx750Dx 750HT:- TOP to be madeof25mmthick Prelaminated particle boardwith PVC edge band, BENT LEGto be CHROME FINISH as per drawing. | nos | ₹ 10,897 |
| 51.30 | Providing & Fixing Curviliner Workstation @ 1500/1500Lx600/600Dx750HT Providing & Fixing Curviliner Workstation @ 1500/1500Lx600/600Dx750HT, Curvilinear Table Top @ 1500/1500Lx600/600D:- TOP to be made of 25 mm thick Prelaminated particle board with PVC edge band, GABLE END to be made of 25 mm thick Prelaminated particle board with PVC edge band, KEYBOARD TRAY ( WITHOUT MOUSE TRAY):- Metal Powder Coated -Black Color, CPUTROLLEY:- Metal Powder Coated - Black Color, along with 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. 3 Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board, | nos | ₹ 15,767 |
| 51.31 | Conference Table @ 3600Lx1400Dx750HT Providing & Fixing of Main Table @ 3600Lx1400Dx750HT - made up of 18+18mm Thick MDF top with PVC Membrane finish and waterfall edge profile. Aluminium Anodizied finish beeding of 4mm thich is running all over the table top edge. Gable ends is Aerofoiled Shape with front edges in PVC Membrane finish and rest in Prelaminated MDF with batton structure. Gable ends should be hollow from inside for the provision of passing electrical and Data wiring., MODESTY PANEL:- to be made of 18 mm thick Prelaminated particle board with PVC edge band Access Flap:- For Wire manager 2 Nos. | nos | ₹ 99,105 |
| 51.32 | Conference Table @ 1800 x 900 x 750 mm Ht. Providing &FixingofMainTable@1800Lx900Dx750HT -madeup of18+18mm Thick MDF top with PVC Membrane finish and waterfall edge profile. Aluminium Anodizied finish beeding of 4mm thich is running all over the table top edge. Gable ends is Aerofoiled Shape with front edges in PVC Membrane finish and rest in Prelaminated MDF with batton structure. Gable ends should be hollow from inside for the provision of passing electrical and Data wiring., MODESTY PANEL:- to be made of 18 mm thick Prelaminated particle board with PVC edge band Access Flap:- For Wire manager 1 Nos. | nos | ₹ 21,108 |
| 51.33 | 12 Seater Reading Table for Library @ 3600Lx1200Dx750HT Providing and Fixing 12 Seater Reading Table for Liberary @ 3600Lx1200Dx750HT Top: made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Gable Ends: made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued byhot melt glue applied byauto edge banding machine. Modesty panel: Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine. | nos | ₹ 29,536 |
| 51.34 | 3 DRAWER PEDESTAL UNIT @ 392L x 450D x 680Ht. mm. 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. 3 Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board. | nos | ₹ 8,108 |
| 51.35 | Low Height Openable Storage @ 900Lx450x750HT Providing and fixing Openable Steel Storage of 900 x 450 x 750Ht, with 2 adjustable shelves, Complete body & shutter made in 0.8 mm thick & Top in 2 mm thick CRCA, 2 Shutter tobemountedwiththehelpofcuphinges, and4adjustablelevelers, enitre storage in powder coated finish with 60 to 80 microns. with 25 mm. thk additional Top on top of storage as as per drawing | nos | ₹ 12,646 |
| 51.36 | Medium Height Steel Storage @ 750Lx450Dx1200HT Providing and fixing Openable Steel Storage of 750 x 450 x 1200Ht, with 2 adjustable shelves, Complete body & shutter made in 0.8 mm thick & Top in 2 mm thick CRCA, 2 Shutter tobemountedwiththehelpofcuphinges, and4adjustablelevelers, enitre storage in powder coated finish with 60 to 80 microns. with 25 mm. thk. as per drawing. | nos | ₹ 15,452 |
| 51.37 | Full Height Steel Storage @ 750Lx450Dx2100HT Providing and fixing Openable Steel Storage of 750 x 450 x 2100Ht, with 4 adjustable shelves, Complete body& shutter made in 0.8 mm thick & Top in 2 mm thick CRCA, 4 Shutter tobemountedwiththehelpofcuphinges, and4adjustablelevelers, enitre storage in powder coated finish with 60 to 80 microns as as per drawing. | nos | ₹ 18,925 |
| 51.38 | Multiple Compartment Lockers @ 1140Lx 457D x 1830 mm. Ht. Providing and fixing Multiple Compartment Lockers @ 1140Lx 457D x 1830 mm. Ht. with 12 Compartments, Complete body & shutter made of CRCA Sheet with powder coated finish as per approved color. | nos | ₹ 43,427 |
| 51.39 | Book Case with Glass Shutter @ 825Lx300Dx1650HT Providing & Fixing of Book Case with Glass Shutter @ 825Lx300Dx1650HT:- To be made out of complete body & in 0.7mm thick CRCA & Shutter in 1.2mm thick CRCA with glass pannel in Powder coating finish as per drawing. | nos | ₹ 26,727 |
| 51.40 | Providing & Arrangemnt of High Back, Synchronized Mechanism withMultiple Locking, Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Leatherite Upholstery | nos | ₹ 17,371 |
| 51.41 | Providing & Arrangemnt of High Back Chair - TILT MECHANISM WITH MULTILOCKING, HIGH DENSITY CUSHION ON SEAT COMPOSITE LEATHER WITH METALLIC SILVER FINISH BASE AND ARMS WITH P.U.CASTORS GASLIFT FOR HEIGHT ADJUSTMENT. | nos | ₹ 15,474 |
| 51.42 | Providing & Arrangemnt of MId Back, Normal Syncro Mechanism, Fixed Armrest, Gaslift for Seat height adjustment, Standard 5-prong/Nylon Base with Leather Upholstery | nos | ₹ 9,563 |
| 51.43 | Providing & Arrangemnt of Mid Back, ECO CTS Mechanism, Fixed Armrest, Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Fabric Upholstery | nos | ₹ 6,520 |
| 51.44 | Public Seating Chair. - 3 Seater Providing and Fixing 3 seater Public seating chair made of complete metal with Legs in Crome finish and seates in silver powder coating finish. | nos | ₹ 18,056 |
| 51.45 | Double Faced Mobile Unit for Compactor 2150mmH x 2745mmW x 900mmD Providing and fixingDouble FacedMobile Unit for Compactor2150mmH x2745mmW x 900mmD - BASE FRAME: Base Frame shall be fabricated in channel Type from minimum 2.5 mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS: The guide rails shall be made out of 28mm Bright bar placed on 1.2 mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE: Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES: Shelves made of 22SWGthick PrimeQualityC.R.C.A. having 10 folds each willbe provided each designedto carrya U.D.L.of 70Kilograms. VERTICALPANEL: Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL: Made out of 22SWG thick C. R.C. A. prime qualitySteel to cover the entire drive mechanism. CENTRE PARTITION: The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING: System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM: Driving Mechanism will be provided externallysupportedon specialgrade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL: Fully Powder Coated three pronged drive wheel for better torque & free movement of therack overthe guiderail. INDEXING ARRANGEMENT: Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH: Powder Coating (8 tanks process with 70 microns). | nos | ₹ 135,808 |
| 51.46 | Single Faced Mobile Unit for Compactor 2150mmH x 2745mmW x 457mmD Providing and fixing Single Faced Mobile Unit for Compactor 2150mmH x 2745mmW x 457mmD - BASE FRAME: Base Frame shall be fabricated in channel Type from minimum 2.5 mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS: The guide rails shall be made out of 28mm Bright bar placed on 1.2 mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE: Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES: Shelves made of 22SWGthick PrimeQualityC.R.C.A. having 10 folds each willbe provided each designedto carrya U.D.L.of 70Kilograms. VERTICALPANEL: Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL: Made out of 22SWG thick C. R.C. A. prime qualitySteel to cover the entire drive mechanism. CENTRE PARTITION: The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING: System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM: Driving Mechanism will be provided externallysupportedon specialgrade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL: Fully Powder Coated three pronged drive wheel for better torque & free movement of therack overthe guiderail. INDEXING ARRANGEMENT: Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH: Powder Coating (8 tanks process with 70 microns). | nos | ₹ 99,768 |
| 51.47 | Single Faced Fixed Unit for Compactor 2150mmH x 2745mmW x 457mmD Providing and fixing Single Faced Fixed Unit for Compactor 2150mmH x 2745mmW x 457mmD - BASE FRAME: Base Frame shall be fabricated in channel Type from minimum 2.5 mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS: The guide rails shall be made out of 28mm Bright bar placed on 1.2 mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE: Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES: Shelves made of 22SWGthick PrimeQualityC.R.C.A. having 10 folds each willbe provided each designedto carrya U.D.L.of 70Kilograms. VERTICALPANEL: Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL: Made out of 22SWG thick C. R.C. A. prime qualitySteel to cover the entire drive mechanism. CENTRE PARTITION: The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING: System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM: Driving Mechanism will be provided externallysupportedon specialgrade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL: Fully Powder Coated three pronged drive wheel for better torque & free movement of therack overthe guiderail. INDEXING ARRANGEMENT: Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH: Powder Coating (8 tanks process with 70 microns). | nos | ₹ 64,014 |
| 51.48 | Double Faced Mobile Unit for Compactor 2150mmH x 1830mmW x 900mmD Providing and fixingDouble FacedMobile Unit for Compactor2150mmH x1830mmW x 900mmD - BASE FRAME: Base Frame shall be fabricated in channel Type from minimum 2.5 mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS: The guide rails shall be made out of 28mm Bright bar placed on 1.2 mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE: Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES: Shelves made of 22SWGthick PrimeQualityC.R.C.A. having 10 folds each willbe provided each designedto carrya U.D.L.of 70Kilograms. VERTICALPANEL: Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL: Made out of 22SWG thick C. R.C. A. prime qualitySteel to cover the entire drive mechanism. CENTRE PARTITION: The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING: System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM: Driving Mechanism will be provided externallysupportedon specialgrade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL: Fully Powder Coated three pronged drive wheel for better torque & free movement of therack overthe guiderail. INDEXING ARRANGEMENT: Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH: Powder Coating (8 tanks process with 70 microns). | nos | ₹ 95,652 |
| 51.49 | Single Faced Mobile Unit for Compactor 2150mmH x 1830mmW x 457mmD Providing and fixing Single Faced Mobile Unit for Compactor 2150mmH x 1830mmW x 457mmD - BASE FRAME: Base Frame shall be fabricated in channel Type from minimum 2.5 mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS: The guide rails shall be made out of 28mm Bright bar placed on 1.2 mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE: Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES: Shelves made of 22SWGthick PrimeQualityC.R.C.A. having 10 folds each willbe provided each designedto carrya U.D.L.of 70Kilograms. VERTICALPANEL: Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL: Made out of 22SWG thick C. R.C. A. prime qualitySteel to cover the entire drive mechanism. CENTRE PARTITION: The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING: System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM: Driving Mechanism will be provided externallysupportedon specialgrade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL: Fully Powder Coated three pronged drive wheel for better torque & free movement of therack overthe guiderail. INDEXING ARRANGEMENT: Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH: Powder Coating (8 tanks process with 70 microns). | nos | ₹ 69,900 |
| 51.50 | Single Faced Fixed Unit for Compactor 2150mmH x 1830mmW x 457mmD Providing and fixing Single Faced Fixed Unit for Compactor 2150mmH x 1830mmW x 457mmD - BASE FRAME: Base Frame shall be fabricated in channel Type from minimum 2.5 mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS: The guide rails shall be made out of 28mm Bright bar placed on 1.2 mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE: Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES: Shelves made of 22SWGthick PrimeQualityC.R.C.A. having 10 folds each willbe provided each designedto carrya U.D.L.of 70Kilograms. VERTICALPANEL: Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL: Made out of 22SWG thick C. R.C. A. prime qualitySteel to cover the entire drive mechanism. CENTRE PARTITION: The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING: System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM: Driving Mechanism will be provided externallysupportedon specialgrade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL: Fully Powder Coated three pronged drive wheel for better torque & free movement of therack overthe guiderail. INDEXING ARRANGEMENT: Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH: Powder Coating (8 tanks process with 70 microns). | nos | ₹ 44,223 |
| 51.51 | Stool for Lab and Class-IV Providing andfixing4leggedLabstool,Legsmadeof16Guage45 MMOuter dimension MS Pipe, Duly painted, With a 304 Grade Stainless steel 12 inch wide seat with a 1 inch collar, Height adjustment via a screw. as per design and drawing and instructions of Engineer in charge. | nos | ₹ 2,617 |
| 51.52 | Alluminium foldable ladder for store Providing & Fixing Foldable Alluminum Ladder 1500 mm. Ht. | nos | ₹ 3,961 |
| 51.53 | Sofa Set 3+1+1 Providing & fixing Sofa Set 3+1+1 Brown and Cream leather DIMENSION Length: 182.5 (cms) Breadth (cms): 100 (cms)Height (cms): 100 (cms) Weight (Kilograms): 66 (Kilogram) Seating Capacity: Five Seat | nos | ₹ 39,612 |
| 51.54 | Tea Table 900mm X 750mm X 450mm for m.s. ante chamber Providing And Fixing Of Tea Table 900mm X 750mm X 450mm With 12mm Thick Colour Eitched Tempered Glass With Bevelled Drawing Made Out Of 18mm Thick Waterproofing Ply. The Outer Laces To Be Finished With High Quality 4 Mm Thik Veneer Or 1 Mm Thik Mica Etc. | nos | ₹ 11,123 |
| 51.55 | Single Bed @ 2025LX 1000DX 650H Providing and fixing Single Bed of Size 2025Lx1000Dx650H with matress and pillow. Understructure: - The legs are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2 mm. The legs should have corner brackets welded to it at two levels. The corner brackets are made of 2mm thick CRCA having a L shaped structure to join the side panels and headboard to the leg. Three nos. of Horizontal stiffeners are provided at equal intervals. The stiffeners are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. The middle Horizontal Stiffener has a leg attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. This leg is also made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. All Metal components to undergo 7 tank treatment process and should be powder coated to the thickness of minimum 50 Microns DFT.Side Panel: - The side panels are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The overall width of the side panel is 150mm. The side panels have 18mm thick prelam particle board Baton running for required length to add rigidity to the structure. Head Board:- The head board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The head board size to be considered as 1000 x 650mm. Foot Board:- The foot board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The head board size to be considered as 1000 x 450mm. BedBase:-TheBedBaseismadeup of12mm thick Prelam ParticleBoard withboth side White laminate. | nos | ₹ 19,367 |
| 51.56 | Dressing Table @400LX 400DX 1800H Providing & Fixing Dressing Table of size 400LX 400DX 1800H.The Dressing table unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The unit has one drawer and one shelf. The dressing table has a mirror of 4mm thick pasted on 18mm thick prelm particle board attached to the base unit. The mirror size considered is 1155 x 360 x 4(t). The mirror has been pasted using high quality 3M sticker. | nos | ₹ 17,352 |
| 51.57 | Wardrobe with Mirror @ 900LX 600DX 1965H Providing andFixingWardrobewithMirrorofsize 900LX600DX 1965H The wardrobe side panels and doors are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The shelves are made of 18mm thick Prelam Particle Board with decorative laminate on both sides. The top is made of 36mm prelam particle board with decorative laminate on both sides. (18mm Prelam Particle board and 18mm batons on all sides to achieve 36mm overall thickness). The exposed edges of the top are sealed with 2mm thick PVC edge Banding. The top most part of the wardrobe has an aluminum hanger rod of EBCO make. One drawer of size 400(W) x 150(H) x 450 (D) made of 18mm thick prelam Particle Board has been considered. The drawer will have a multipurpose lock of EBCO premium make. The wardrobe handles are Satin SS finish of 160mm pitch. The wardrobe has a multipurpose lock of EBCO make. All hinges considered are Hettich make. Necessary good quality hardwares have been considered as required. | nos | ₹ 40,389 |
| 51.58 | Bed Side Table @ 400LX 400DX 415H Providing and Fixing Bed Side Table of size 400LX 400DX 415H The bed side unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The bed side table has one drawer and one shelf. The shelf is made of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding | nos | ₹ 6,401 |
| 51.59 | Kitchen Trolley Providing and Fixing stainless steel kitchen trolley of overall 26 " height and 22" depth,supported on aluminium pipes,trolley basket made out of 5 mm stainless steel rod fitted on telescopic channel of size 1.5 " x 20 " x 22 " on both sides of trolley of 12 " or above size, panel having 40Kilogramload bearing capacity of trolley made out of 20 mm PUC coated plywood and colour combination as directed by E-I-C.Inner side of panel covered bywhitemica,100mms.s. decorativehandle.(The widthand height of individual compartments shall be kept as directed by Engineer-in-charge) | rmt | ₹ 16,125 |
| 51.60 | Solid Core Flush door Single leaf Providing and fixing factory made solid core flush door in single leaf 35 mm thick, decorative types, of exterior grade, as per detailed drawings, conforming to I.S.:2202 - 1962 (Revised) with approved face veneers on both faces with/without glazing and venetians in the positions shown on the drawings or as directed, all necessary beads, moulding and lipping, holdfasts, mat finish stainless steel fixtures fastenings, finishing with french-polish/ waxing complete. (without door frame).(Sample to be got approved from Ex.Engineer before use) Commercial Hard Wood shutter | sqm | ₹ 2,750 |
| 51.61 | Solid Core Flush door Double leaf Providing and fixing factory made solid core flush door shutters in double leaves 35mm thick,decorative type of exterior grade, as per detailed drawings, conforming to I.S.: 2202 – 1966 (Revised) including approved face veneers on both sides, without glazing and venetians including mat finish stainless steel fixtures and fastening, stoppers and finishing with french polishing etc. (Excluding door frame)(Sample to be got approved from Ex. Engineer before use) Commercial Hard Wood shutter | sqm | ₹ 3,100 |
| 51.62 | Providing Silica plaster plaster externally in two coats in all positions including base coat of 8 to 10 mm thick curing the same for not less than two days and keeping the surface of base coat rough to receive the final coat treatment 5 to 7 mm thick.finishing the surface by taking out grains and curing for 8 to 10 daysscaffolding etc complete.(The silica plast material shall contain 53 grade OPC cement with pozzolanic materials.size of agreegates shall be of 3 mm having 1:3 proportion with cement. | sqm | ₹ 560 |
| 51.63 | Providing and Fixing toilet set for differently Abled persons consist of Floor Mounted white vitreous china water Closet including 6 litre capacity white vitreous china flushing Cistern with raised soft-push button, white vitreous china wash basin of size 46 x 36 cm and one no SS 304 hinged rail 76 cms & three no SS 304of (Grab Bar) 60 cms all including cutting and making good the walls and floors wherever required,seat cover, cistern & wash basin fittings,nuts, bolts and gasket etc complete as per the direction of Engineer-In-charge. | nos | ₹ 70,780 |
| 51.64 | Providing and fixing ISImarked double swing flush door shutters conforming to IS:2202 (Part I) Non-decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel L- hinges with necessary screws Fittings & Fixtures per leaf SS kick plates on both sides of the door of 300mm height Heavy Duty satin finish butt SS Hinges (100mm x 75mm x 3mm in size) -4 nos. SS finished lever handle with mortise lock- 1 One Number Floor spring- 1 One Number 100mm x 100mm safety glass at the specified location | sqm | ₹ 12,500 |
| 51.65 | Providing and applying blue and white coloured thermoplastic road marking paints for marking a 3ft x 3 ft universal accessibility symbol within the parking bay as paer the drawings and up to the satisfaction of the engineer in charge. | nos | ₹ 1,575 |
| 51.66 | Acrylic tactile audio map Design, supply,fabrication andfixingofacrylic,nonglare,tactileaudiopictorial building layout as per the approved size, design and make, having 6mm thick acrylic non glare base plate of the approved colour and non glare acrylic cut out symbols and upper case Sans Serif letters of 12mm height, raised 3mm above base plate and Grade 2/ Grade 1 Braille to be integral with the sign face and be raised 0.5mm above baseplate. Themap to be installed at the specified location as per accessibilitystandards, shall be oriented to the position of the viewer and to be installed at a height of 800 mm from the finished ground/ floor level and using the necessary hardware specified by the manufacturer and to be installed up to the satisfaction of the engineer in charge | nos | ₹ 20,790 |
| 51.67 | Directional signage Design, supply, fabrication and fixing acrylic multilingual Braille (raised dots) directional signboards of size 6" x 9" designed as per accessibility standards and having 4mm thick acrylic base plate with Upper Case San Serif words made of white acrylic non glare cut out letters of height 15mm raised not less than 0.8mm above base plate and the equivalent word written in Hindi with Devnagri non glare acrylic letters of height 15mm raised not less than 0.8mm above base plate and having a non glare acrylic cut arrow pointing in the required direction. Each signboard to be fixed as per manufacturers specifications on the wall at the approved location and at a height of 1200mm from FFL and as per the directions by the engineer in charge. | nos | ₹ 1,633 |
| 51.68 | Floor Directories Providing and fixing acrylic multilingual Braille (raised dots)ADA compliant modular floor directories system on all floors of size1.5' x 2', showing the floor plan and the list of rooms on that floor, to be installed on each floor near the staircase, designed as per standards and having 4mm thick blue acrylic base plate with Upper Case San Serif words and symbols made of white acrylic non glare cut out letters of height 20mm raised not less than 0.8mm above base plate and the equivalent word/s written in Hindi with Devnagri non glare imported acrylic letters of height 15mm raised not less than 0.8mm above base plate. Grade 2/ Grade 1 Braille to be integral with the sign face and be raised 0.5mm above base plate. Each directory to be fixed as per manufacturers specifications on the wall at the approved location at a height of 1200mm from FFL and as per the directions by the engineer in charge. | nos | ₹ 17,418 |
| 51.69 | Providing an ADA compliant Disability Service Desk having a lowered portion (800mm from FFL) and leg space of 450 mm, having the approved design and of the approved make as per manufacturers specifications | nos | ₹ 22,000 |
| 51.70 | Providing and fixing SS-304 studs having 35mm dia. of the approved brand and make inside the building on all floors in corridors, lobbies level differences etc. as per accessibility standards and as per the installation instructions prescribed by the manufacturer, using the necessaryadhesive including finishing work up to the satisfaction of the engineer in charge complete. | nos | ₹ 59 |
| 51.71 | Providing and fixing SS-304 strips of size 280mm x 35mm of the approved brand and make inside the building on all floors in corridors, lobbies level differences etc. as per accessibility standards and as per the installation instructions prescribed by the manufacturer, using the necessaryadhesive including finishing work up to the satisfaction of the engineer in charge complete. | nos | ₹ 293 |
| 51.72 | Providing and fixing Braille indicators for handrails of the approved design and make having Braille dots raised 0.5mm above base plate, to be installed at the specified locations as per the directions of the engineer in charge | nos | ₹ 1,500 |
| 51.73 | Providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts, etc. of the required size on the top of the floor of the side of waiste slab with suitable arrangement as per approval of engineer in charge (for payment purpose, onlythe weight of the stainless steel members shall be considered excluding fixing accessories such as nut bolts, fasteners etc.). 50mm dia. pipe, 1.5mm thickness and weight 1.92Kilogram/ r. metre | kg | ₹ 694 |
| 51.74 | ADAcompliant modular Multilingualand tactileEmergencyevacuation map ofeach floor indicating the current position of the viewer saying "YOU ARE HERE" of 15mm height letters in red with white bacKilogramround, indicating the emergency exits, locations of fire extinguishers etc. Signs shall have a solid header with the text “EVACUATION PLAN” in contrasting uppercase letters no less than 3/4" in height. The size of the board shall be 2ft x 2ft and shall be installed at a height of 1200mm from FFL and shall be oriented to the position of the viewer as per the direction of the site engineer | nos | ₹ 19,750 |
| 51.75 | Fire exit and floor identification signage as per manufacturer's specifications, ADA compliant and modular system | nos | ₹ 7,500 |
| 51.76 | Supplying and installing of in position the signages "FIRE ORDER"it shouldcontain the following matter on 3mm thick "Opaque" PVC foam board of computerized cut, PVC Non-reflective self adhesive vinyle painted foam board of 3' x 4'.Product to be ADA compliant and modular system. | nos | ₹ 19,780 |
| 51.77 | Providing an emergency evacuation chair of the approved design, weight and loading capacity | nos | ₹ 73,500 |
| 51.78 | Providing and fixing the reader of the approved brand and make as per the manufacturers specifications and as per the directions of the engineer in charge | nos | ₹ 23,100 |
| 51.79 | Providing and fixing the transmitter of the approved brand and make on each floor as per the manufacturers specifications and as per the directions of the engineer in charge | nos | ₹ 3,675 |
| 51.80 | Providing and fixing SS Braille buttons in the elevator of the approved brand and make to be installed using the specified adhesive and as per the instructions given by the manufacturer | nos | ₹ 189 |
| 51.81 | Providing and fixing of high intensity reflective conspicuity tape 25 to 50mm width, on edges of treads in staircase including, cutting, pasting etc. of make 3M or equivalent brand as per the direction of engineer in charge | rmt | ₹ 160 |
| 51.82 | Providing a folding wheelchair of Pioneer Surgicals Brand, model One Number PS 809/ equivalent make as per the directions of the engineer in charge. | nos | ₹ 8,950 |
| 51.83 | Design, supply, fabrication and fixing of SS, non glare Signage board (2 ft. x 2 ft.- 1 One Number) for the accessible parking, as per the approved design and make, having 1.2mm thick SS non glare base plate and Grade 2/ Grade 1 Braille (raised dots)to be etched/ engraved and be raised 0.5mm above base plate and Upper Case San Serif words and Universal Accessibility Symbol to be etched/ engraved and signage to be installed at a height of2100mmfromthegroundlevelusingapost ofMS hollow squaresection (50mm x 50mm) as per the installation procedure specified by the manufacturer and as per accessibility standards and up to the satisfaction of the engineer in charge. | nos | ₹ 23,100 |
| 51.84 | Design, supply, fabrication and fixing of SS, non glare multilingual Braille (raised dots) entrance signage (size 1 ft x 1 ft) as per the approved design and make,indicating the name of the building. Having 1.2mm thick SS non glare blue coloured base plate with the 'Universal Accessibility Symbol' and Upper case Sans Serif words of height 15mm engraved on it along with the equivalent word/ s written in Hindi using Devnagri script of height 15mm in white colour. Grade 2/ Grade 1 Braille to be etched/ engraved and be raised 0.5mm above base plate.The signage to be installed at the specified location on the compound wall near the site entrance gate installed at a height of 1200 mm from the finished ground/ floor level, using the necessary hardware specified by the manufacturer and to be installed up to the satisfaction of the engineer in charge. | nos | ₹ 5,969 |
| 51.85 | Providing and laying in place 300mm x 300mm x 16mm cement tactile directional and warning tiles (for a person with visual impairment)of the approved brand and make and specified colour for outdoor floors such as footpath, courtyard, multimodals location etc. laid on 20mm thick base of cement mortar 1:4 (1 cement: 4 coarse sand) in all shapes and patterns including grouting the joints with white cement with matching pigments etc. complete as per direction of engineer in charge | sqm | ₹ 1,550 |
| 51.86 | Providing and laying in place 300mm x 300mm x 9.8mm vitrified tactile warning and directional tiles of the approved brand, make and colour inside the buildings at in all corridors and lobbies, level differences etc. as per accessibility standards and as per the installation instructions prescribed by the manufacturer including zarri making wherever required and finishing including grouting the joints with white cement with matching pigments etc. up to the satisfaction of the engineer in charge complete. | sqm | ₹ 2,200 |
| 51.87 | Design, supply, fabrication and fixing acrylic multilingual Braille (raised dots) signboards of size 6"x 9" for room titles, designed as per the drawings issued and having 4mm thick blue acrylic base plate with Upper Case San Serif words made of white acrylic non glare cut out letters of height 15mm raised not less than 0.8mm above base plate and the equivalent word/s written in Hindi with Devnagri non glare acrylic letters of height 15mm raised not less than 0.8mm above base plate. Grade 2/ Grade 1 Braille to be integral with the sign face and be raised 0.5mm above base plate.Each signboard to be fixed as per manufacturers specifications on the wall adjoining the respective room door at a height of 1200mm from FFL and as per the directions by the engineer in charge. | nos | ₹ 1,633 |
| 51.88 | Providing and fixing in place 300mm x 300mm x 3mm polyurethane stick on tactile directional tiles and warning tiles having beveled edges and of the approved brand, make and colour and conforming to ISO 23599: 2012 inside the building on all floors in corridors, lobbies, level differences as per accessibility standards and to be installed as per the installation instructions given by the manufacturer using butyl rubber adhesive and the hardware specified by the manufacturer, as per the direction of the engineer in charge complete. | nos | ₹ 3,545 |
| 51.89 | Grab bars-Providing SS grab bars set for accessible toilets comprising of 4 nos. Grab bars as specified below.(1 nos. wing grab bar + 1 nos. L shaped grab bar + 2 nos. straight grab bars = 1 typical set) 27a) Swing grab bar (1 NOS) Providing a S.S. 304 SWING HANDICAP GRAB BAR - 700 mm and of DIA: 32MM and thickness 1.5mm of the roved brand and make. 27b) L Shaped grab bar (1 NOS) Providing S.S. 304 L SHAPED DISABLED GRAB BAR of IZE-600MM (H) X 600MM (D) and 32MM DIA. and thickness mm of the approved brand and make. 27c) Straight grab bar(2 NOS) Providing S.STEEL304 GRABRAIL(600MM),32MM DIA. and thickness 1.5mm of the approved brand and make. | nos | ₹ 19,500 |
| 51.90 | Providing and Fixing Accessible Wayfinding and navigation signage systems - Providing and fixing in location as diected by Engineer in Charge, accessible modular wayfinding and navigational signage system comprising of ADA and Harmonised Guidelines compliant sigange and wayfinding elements, in multilingual, tactile and braille format. Sigange systems to be designed for entire building / complex under consideration | nos | ₹ 85,640 |
| 51.91 | Providing & fixingfactory-made steeldoor ofSingle leafExternal EmbossedWood finish type with a.) frame of size 100x58 mm conforming to IS: 4351-2003, 1.2 mm thick pre galvanized sheet with mitredand weldedcones,frame stretches, hinge reinforcing plates, fixing plates and hardware mounting plates and Polyurethane foam infill b.) Shutter of thickness 46mmmade of0.8 mmthick slipcoated pregalvanized steelsheet onboth sides conforming to ASTM A527/ASTM A525, BS 29891994, IS 277,Zinc coating 120 GSM. Lock formed panels with internal stiffeners of 3mm thick made of galvanized sheet, 3 mm thick hinge reinforcing hardware mounting plates and lock protection with Honey- comb craft paper infill of thickness 150 GSM of load bearing capacity500Kilogram/ One Square Metre. c.) Finish: Powder coated surface finished with thermosetting polyurethane paint ofAliphaticgradeofthickness 60-micrond.) Accessories:Min8Anchorfastener of HILTImake, min 3 SS Ball Bearing Butt Hinges ofDorset make, Dorset Mortiselock, SS Tower bolt of 200 mm size, Eye hole, Door stopper complete. | sqm | ₹ 6,368 |
| 51.92 | Providing & fixing factory-made steel door of Single leaf External Plain Wood finish type with a.) frame of size 100x58 mm conforming to IS: 4351-2003, 1.2 mm thick pre galvanized sheet with mitredand weldedcones,frame stretches, hinge reinforcing plates, fixing plates and hardware mounting plates and Polyurethane foam infill b.) Shutter of thickness 46mmmade of0.8 mmthick slipcoated pregalvanized steelsheet onboth sides conforming to ASTM A527/ASTM A525, BS 29891994, IS 277,Zinc coating 120 GSM. Lock formed panels with internal stiffeners of 3mm thick made of galvanized sheet, 3 mm thick hinge reinforcing hardware mounting plates and lock protection with Honey- comb craft paper infill of thickness 150 GSM of load bearing capacity500Kilogram/ One Square Metre. c.) Finish: Powder coated surface finished with thermosetting polyurethane paint ofAliphaticgradeofthickness 60-micrond.) Accessories:Min8Anchorfastener of HILTImake, min 3 SS Ball Bearing Butt Hinges ofDorset make, Dorset Mortiselock, SS Tower bolt of 200 mm size, Eye hole, Door stopper complete. Sizes up to 1200 x2439 mm (cid:10) | sqm | ₹ 6,080 |
| 51.93 | Providing & fixing factory-made steel door of Single leaf External Plain Wood finish type with a.) frame of size 100x58 mm conforming to IS: 4351-2003, 1.2 mm thick pre galvanized sheet with mitredand weldedcones,frame stretches, hinge reinforcing plates, fixing plates and hardware mounting plates and Polyurethane foam infill b.) Shutter of thickness 46mmmade of0.8 mmthick slipcoated pregalvanized steelsheet onboth sides conforming to ASTM A527/ASTM A525, BS 29891994, IS 277,Zinc coating 120 GSM. Lock formed panels with internal stiffeners of 3mm thick made of galvanized sheet, 3 mm thick hinge reinforcing hardware mounting plates and lock protection with Honey- comb craft paper infill of thickness 150 GSM of load bearing capacity500Kilogram/ One Square Metre. c.) Finish: Powder coated surface finished with thermosetting polyurethane paint ofAliphaticgradeofthickness 60-micrond.) Accessories:Min8Anchorfastener of HILTImake, min 3 SS Ball Bearing Butt Hinges ofDorset make, Dorset Mortiselock, SS Tower bolt of 200 mm size, Eye hole, Door stopper complete. Sizes up to 1200 x2439 mm (cid:10) | sqm | ₹ 5,790 |
| 51.94 | Providing & fixing factory-made steel door of Single leaf Internal Plain Wood finish type with a.) frame of size 100x58 mm conforming to IS: 4351-2003, 1.2 mm thick pre galvanized sheet with mitredand weldedcones,frame stretches, hinge reinforcing plates, fixing plates and hardware mounting plates and Polyurethane foam infill b.) Shutter of thickness 46mmmade of0.8 mmthick slipcoated pregalvanized steelsheet onboth sides conforming to ASTM A527/ASTM A525, BS 29891994, IS 277,Zinc coating 120 GSM. Lock formed panels with internal stiffeners of 3mm thick made of galvanized sheet, 3 mm thick hinge reinforcing hardware mounting plates and lock protection with Honey- comb craft paper infill of thickness 150 GSM of load bearing capacity500Kilogram/ One Square Metre. c.) Finish: Powder coated surface finished with thermosetting polyurethane paint ofAliphaticgradeofthickness 60-micrond.) Accessories:Min8Anchorfastener of HILTI make, min 3 SS Ball Bearing Butt Hinges of Dorset make, Dorset cylindrical lock, SS Tower bolt of 200 mm size, Door stopper complete. (cid:10) | sqm | ₹ 5,509 |
| 51.95 | Providing & fixing factory-made steel door of Single leaf Internal Plain Steel finish type with a.) frame of size 100x58 mm conforming to IS: 4351-2003, 1.2 mm thick pre galvanized sheet with mitredand weldedcones,frame stretches, hinge reinforcing plates, fixing plates and hardware mounting plates and Polyurethane foam infill b.) Shutter of thickness 46mmmade of0.8 mmthick slipcoated pregalvanized steelsheet onboth sides conforming to ASTM A527/ASTM A525, BS 29891994, IS 277,Zinc coating 120 GSM. Lock formed panels with internal stiffeners of 3mm thick made of galvanized sheet, 3 mm thick hinge reinforcing hardware mounting plates and lock protection with Honey- comb craft paper infill of thickness 150 GSM of load bearing capacity500Kilogram/ One Square Metre. c.) Finish: Powder coated surface finished with thermosetting polyurethane paint ofAliphaticgradeofthickness 60-micrond.) Accessories:Min8Anchorfastener of HILTI make, min 3 SS Ball Bearing Butt Hinges of Dorset make, Dorset cylindrical lock, SS Tower bolt of 200 mm size, Door stopper complete. | sqm | ₹ 5,211 |
| 51.96 | Providing & fixing factory-made Single leaf 2 hour fire rated door as per IS 3614 Part 2 & BS 476 Part 20 & 22, tested to UL 10 C and conforming to NFPA 80, tested at NTL /CBRI/ARAIofPlain Steelfinish typewitha.)Frameofsize 143x58mm andthickness of 1.6 mm thick skin pass galvanized iron sheet (Conform to IS 277) formed to single or double rebate profile b.) Shutter of 46 mm thickness and constructed from 1.2 mm thick skin pas galvanized iron sheet (Conform to IS 277) infill Rockwool / Mineral wool/ Honey comb craft paper c.) Vision glass of 5mm thick clear/wired glass Circular or Rectangular d.) Finish: Primed with zinc phosphate stoving primer and finished with Polyurethane aliphatic grade or epoxy paint as required of thickness 60 micron e.) Accessories: Min 8 Anchor fastener of HILTI make, min 3 SS Ball Bearing Butt Hinges, Mortise sash lock with lever handle, Mortise dead bolt, Mortise latch, Door closer and Flush bolts complete. (cid:10) | sqm | ₹ 7,236 |
| 51.97 | Providing & fixing factory-made Single leaf 2 hour fire rated door as per IS 3614 Part 2 & BS 476 Part 20 & 22, tested to UL 10 C and conforming to NFPA 80, tested at NTL /CBRI/ARAIofPlain Steelfinish typewitha.)Frameofsize 143x58mm andthickness of 1.6 mm thick skin pass galvanized iron sheet (Conform to IS 277) formed to single or double rebate profile b.) Shutter of 46 mm thickness and constructed from 1.2 mm thick skin pas galvanized iron sheet (Conform to IS 277) infill Rockwool / Mineral wool/ Honey comb craft paper c.) Vision glass of 5mm thick clear/wired glass Circular or Rectangular d.) Finish: Primed with zinc phosphate stoving primer and finished with Polyurethane aliphatic grade or epoxy paint as required of thickness 60 micron e.) Accessories: Min 8 Anchor fastener of HILTI make, min 3 SS Ball Bearing Butt Hinges, Mortise sash lock with lever handle, Mortise dead bolt, Mortise latch, Door closer, Panic bar and external trim lock and Flush bolts complete. (cid:10) | sqm | ₹ 8,686 |
| 51.98 | Providing & fixing factory-made Aluminum windows of aluminum alloy HE 9WP (6063 T5/T6), powder coating of jotun/AkzoNobel of 60 micron thickness a.) Glass: 5mm thick clear float of Saint Gobain / Asahi make b.) Mesh of SS Type 304 grade of.22 mm thickness c.) Accessories: EPDM (Ethylene Propylene Diene Monomer) Gasket, SS Screws, Aluminum cleats, Roller, Push handle, Fly mesh handle, Anti lifter, U guide glass and mesh shutter complete | sqm | ₹ 5,471 |
| 51.99 | Providing & fixing factory-made steel windows constructed of Skin Pass Galvanized Iron Sheet (as per IS 513 “D" Quality, Galvanized as per IS 277 with Hot Zinc Coating of 120 grams / Sq.Mtr& thickness of 0.6 mm) with a.) Window Shutter of.6mm thick skin pass Galvanized lron Sheet b.) WindowFrames of.8m thick skin pass Galvanized Ironsheet of size 80mm X 45mm c.) Mullion: of 0.8mmthick skin pass Galvanized lron sheet of size 80mm X 60mm d.) Vision Glass of 4mm clear float glass in rectangular shape. e.) Finish: Coated with Zinc Phosphate Primer or Thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability f.) MS Grill of 10 mm square MS bright bars g.) Accessories: SS Pin type Hinges — 1 Set; Polypropylene, Handle — 1, Friction StayPowder Coated – 1, MS powder coated Tower bolt — 2 (Ethyl Propylene Diamine Monomer (EPDM) Should be used all around glass in shutter for fixing of glass); corner brackets — 4 (made of Polypropylene each per shutter and frame) complete | sqm | ₹ 6,383 |
| 51.100 | Providing,aupplying,fabricating and fixing panel of aluminium composite panel cladding in approved shape made out of 4 mm thick ACP sheet material consisting of 3mm thick FR grade mineral core following NBC part IV Fire and life safety (having 2 hours fire resistance in accordance to ASTM E119-12 and BS476 part 6 and 7 class O) sandwitched between two aluminium sheets (each 0.5 mm thick of AA 5005/AA3105 grade) The aluminium composite panel cladding sheet shall be coil coated with kynar 500 based PVDF/Lumiflon based fluropolymer resin (having 70:30 ratio of PVDF and acrylic) coating of approved colour and sg=hade on top face and polymer (service) coating of bottom face as specified using stainless steel screws,nuts,bolts,washers,cleats,weather silicon sealent,backer rods etc.overall weight of the ACP shall not be less than 7.5 Kilogram/ One Square Metre) | sqm | ₹ 3,870 |
| 51.101 | Providing internal cement plaster 25 mm thick in single coat using Ready to use wall plaster in cement mortar 1:4 to concrete, brick, stone surfaces in all positions including scaffolding and curing. Providing groove at joint of B.B. Masonry and concrete members complete. With Prior Approval of Concerned S.E. | sqm | ₹ 538 |
| 51.102 | Providing internal cement plaster 20mm thick in a single coat using Ready to use wall plaster to concrete, brick surfaces in all positions including scaffolding and curing. Providing groove at joint of B.B.Masonry and concrete members complete. a) cement ratio 1:5 With Prior Approval of Concerned S.E. | sqm | ₹ 456 |
| 51.103 | Providing internal cement plaster 20mm thick in a single coat using Ready to use wall plaster to concrete, brick surfaces in all positions including scaffolding and curing. Providing groove at joint of B.B.Masonry and concrete members complete. b) cement mortar 1:4 With Prior Approval of Concerned S.E. | sqm | ₹ 470 |
| 51.104 | Providing internal cement plaster 20mm thick in a single coat using Ready to use wall plaster to concrete, brick surfaces in all positions including scaffolding and curing. Providing groove at joint of B.B.Masonry and concrete members complete C) cement mortar 1:3 With Prior Approval of Concerned S.E. | sqm | ₹ 484 |
| 51.105 | Providing internal cement plaster 20mm thick in a single coat using Ready to use wall plaster in cement mortar 1:3 to stone masonry surfaces in all positions including scaffolding and curing. Providing groove at joint of stone masonryand concrete members complete. With Prior Approval of Concerned S.E. | sqm | ₹ 484 |
| 51.106 | Providing internal cement plaster 12 mm thick in a single coat using Ready to use wall plaster to concrete or brick surface in all positions including scaffolding and curing complete. Providing groove at joint of B.B. Masonry and concrete members complete. a) cement ratio 1:5 With Prior Approval of Concerned S.E. | sqm | ₹ 235 |
| 51.107 | Providing internal cement plaster 12 mm thick in a single coat using Ready to use wall plaster to concrete or brick surface in all positions including scaffolding and curing complete. Providing groove at joint of B.B. Masonryand concrete members complete. b) cement ratio 1:4 With Prior Approval of Concerned S.E. | sqm | ₹ 249 |
| 51.108 | Providing internal cement plaster 12 mm thick in a single coat using Ready to use wall plaster to concrete or brick surface in all positions including scaffolding and curing complete. Providing groove at joint of B.B. Masonry and concrete members complete. c) cement ratio 1:3 With Prior Approval of Concerned S.E. | sqm | ₹ 260 |
| 51.109 | Providing internal cement plaster 6 mm thick in a single coat using Ready to use wall plaster in cement mortar 1:3 to concrete surface in all positions including scaffolding and curing. Providing groove at joint of B.B.Masonry and concrete members complete. With Prior Approval of Concerned S.E. | sqm | ₹ 198 |
| 51.110 | Providing Autoclaved areated concrete block masonry of approved manufacture confirming to IS 2185 Part III 1984 of size 600 mm x 200mm and thickness 100,150, 200 or 250 mm using Readyto use BLOCK JOINT MORTAR1:6 infoundations andplinth of innerwalls/ externalwallsincludingbailing out water, striking joints onunexposed faces, racking out joints on exposed faces and watering complete. With Prior Approval of Concerned S.E. | cum | ₹ 7,561 |
| 51.111 | Providing and fixing 50mm diameter and 1.5 mm thick vertical and top Stainless steel hand railingin S.S.304 Grade with Stainless steelsquare / circular pipebracing ofsize 32 mm x32mm x1.5 mm in 3 rows including fabricating,fixtures, errecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete | rmt | ₹ 3,462 |
| 51.112 | Providing and installing bio digester unit based on DRDO technology made of fibre reinforced plastic (FRP) having composition and following technical specifications and including necessary pipe and accessories up to 3 meter length, excluding the necessary excavation for installing the bio digester. Percentage of fibre glass (glass content in fibre glass should be minimum 30%): -33.33% Percentage of polyester resin: - 66.67% Water absorption (as per ASTM):-0.30% Flammability as per ASTM Tensile strength:-115 MPA Specific Gravity at 25 degree centigrade 1.45 Izod impact strength:-65KJ/M2 Heat defection/distort temperature:-65deg C Corrosion resistance (Non Corrosive) fitted with Inlet pipe size rigid PVC: -100mm Outlet pipe size rigid PVC:-80mm Gas outlet rigid PVC with Valve: 20mm Bacteria immobilization PVC mattes (on all partition) With DRDO TOT licensee and latest batch certificate(month & year of supply) and capacity as below | ||
| 51.112a | Up to 10 user size (1.0mx1.0mx0.70m), Capacity of biodgester:-700 liters, Area of top, bottom and side walls: - 4.80 sq.m, Area of partition walls: 1.40sq.m, Total weight of FRP: - 33.48 Kilogram, Bacteria inoculums quantity: - 200 liters, Minimum thickness of side walls / top and bottom: 3mm, One Number of inside partitions: - 3, Minimum thickness of partition wall: 3mm. | nos | ₹ 40,565 |
| 51.112b | Up to 15 user size (1.0mx1.0mx1.0m), Capacityof biodgester:-1000 liters, Area of top, bottom and side walls: - 6 sq.m, Area of partition walls: 2 sq.m, Total weight of frp: - 54 Kilogram, Bacteriainoculumsquantity:-400liters, Minimumthickness ofsidewalls/ top and bottom: 4mm, One Number of inside partitions: - 3, Minimum thickness of partition wall: 3mm | nos | ₹ 68,345 |
| 51.112c | Up to 25 user size (1.5mx1.0mx1.0m), Capacityof biodgester:-1500 liters, Area of top, bottom and side walls:- 8 sq.m, Area of partition walls: 2 sq.m, Total weight of frp: - 82.80 Kilogram, Bacteria inoculums quantity: - 600 liters, Minimum thickness of side walls / top andbottom: 5mm,One Numberof insidepartitions: -3, Minimumthickness of partition wall: 3mm | nos | ₹ 93,175 |
| 51.112d | Up to 40 user size (2.0mx1.0mx1.0m), Capacityof biodgester:-2000 liters, Area of top, bottom and side walls: - 10 sq.m, Area of partition walls: 3 sq.m, Total weight of frp: - 106.20 Kilogram, Bacteria inoculums quantity: - 600 liters, Minimum thickness of side walls / top andbottom: 5mm,One Numberof insidepartitions: -3, Minimumthickness of partition wall: 3mm | nos | ₹ 123,978 |
| 51.112e | Up to 60 user size (2.4mx1.25mx1m), Capacityof Biodigester:-3000 liters, Areaof top, bottom and side walls: - 13.30 sq.m, Area of partition walls: 3.75sq.m, Total weight of FRP: - 139.95 Kilogram, Bacteria inoculums quantity: - 1000 liters, Minimum thickness of side walls / top and bottom: 5mm, One Number of inside partitions: - 3, Minimum thickness of partition wall: 3mm | nos | ₹ 163,261 |
| 51.112f | Up to 80 user size (2.7mx1.5mx1m), Capacity of Biodigester:-4000 liters, Area of top, bottom and side walls: - 16.50 sq.m, Area of partition walls: 4.50sq.m, Total weight of FRP: - 202.50 Kilogram, Bacteria inoculums quantity: - 1400 liters, Minimum thickness of side walls / top and bottom: 6mm, One Number of inside partitions: - 4, Minimum thickness of partition wall: 3mm | nos | ₹ 236,232 |
| 51.112g | Up to 100 user size (2.5mx2mx1m), Capacity of Biodigester:-5000 liters, Area of top, bottom and side walls: - 19.00 sq.m, Area of partition walls: 8.00sq.m, Total weight of FRP: - 248.40 Kilogram, Bacteria inoculums quantity: - 1800 liters, Minimum thickness of side walls / top and bottom: 6mm, One Number of inside partitions: - 4, Minimum thickness of partition wall: 3mm | nos | ₹ 290,862 |
| 51.112h | Up to 150 user size (3.2mx2.0mx1.25m), Capacity of Biodigester:-8000 liters, Area of top, bottom and side walls: - 25.80 sq.m, Area of partition walls: 10.00sq.m, Total weight of FRP: - 397.08 Kilogram, Bacteria inoculums quantity: - 3200 liters, Minimum thickness of side walls / top and bottom: 7mm, One Number of inside partitions: - 4, Minimum thickness of partition wall: 4mm | nos | ₹ 466,876 |
| 51.112i | Up to 200 user size (4mx2.0mx1.25m), Capacity of Biodigester:-10000 liters, Area of top, bottom and side walls: - 31.00 sq.m, Area of partition walls: 10.00sq.m, Total weight of FRP: - 462.60 Kilogram, Bacteria inoculums quantity: - 3400 liters, Minimum thickness of side walls / top and bottom: 7mm, One Number of inside partitions: - 4, Minimum thickness of partition wall: 4mm | nos | ₹ 549,936 |
| 51.112j | Up to 300 user size (4.8mx2.0mx1.25m), Capacity of Biodigester:-12000 liters, Area of top, bottom and side walls: - 36.20 sq.m, Area of partition walls: 10.00sq.m, Total weight of FRP: - 593.28 Kilogram, Bacteria inoculums quantity: - 4200 liters, Minimum thickness of side walls / top and bottom: 8mm, One Number of inside partitions: - 4, Minimum thickness of partition wall: 4mm | nos | ₹ 689,174 |
| 51.112k | Up to 400 user size (5mx2.0mx1.5m), Capacity of Biodigester:-15000 liters, Area of top, bottom and side walls: - 41.00 sq.m, Area of partition walls: 12.00sq.m, Total weight of FRP: - 678.80 Kilogram, Bacteria inoculums quantity: - 5200 liters, Minimum thickness of side walls / top and bottom: 8mm, One Number of inside partitions: - 4, Minimum thickness of partition wall: 4mm | nos | ₹ 800,153 |
| 51.112l | Up to 500 user size (6mx2.0mx1.6m), Capacity of Biodigester:-20000 liters, Area of top, bottom and side walls: - 50.72 sq.m, Area of partition walls: 13.36sq.m, Total weight of FRP: - 917.86 Kilogram, Bacteria inoculums quantity: - 7000 liters, Minimum thickness of side walls / top and bottom: 9 mm, One Number of inside partitions: - 4, Minimum thickness of partition wall: 4mm | nos | ₹ 1,081,250 |
| 51.113 | Providing and laying Hyperplas Aluminium or equivalent polymeric multiple monolithic five layer water proofing flexible, pliable and high tensile strength membrane (3 Kilogram/ One Square Metre) which is comprise of top with "V" shape embossed 40 micron Aluminium foil to bear thermal expansion and avoiding delamination & consist of centre core of 90 micron thick High Molecular High density Polyethylene film (HMHDPE) which is protected on both the side with polymeric mix. Applying the membrane by thermofusing to roof & parapet after applying thin film of hot blown bitumen 85/25 or 90/15 grade @ 1.2 Kilogram/ One Square Metre maximum as per surfacecondition orHyperplasprimer@250gms/ OneSquareMetreaspersite condition on the surface to be treated with 10 cm overlapping including finishing etc. complete and covering guarantee of 7 years on stamp paper of Rs. 100/- and as directed byEngineer-in- charge. (Prior permission of S.E.in writing is necessary before inclusion of this item in estimate). | sqm | ₹ 853 |
| 51.114 | Providing and laying Hyperplas standard or equivalent polymeric multiple monolithic five layer water proofing flexible, pliable and high tensile strength membrane (3 Kilogram/ One Square Metre) & consist of centre core of 90 micron thick High Molecular High density Polyethylene film (HMHDPE) which is protected on both the side with polymeric mix. Applying the membrane by thermofusing to roof & parapet after applying thin film ofhot blownbitumen85/25or 90/15grade @1.2 Kilogram/ One SquareMetre maximum as per surface condition or Hyperplas primer @ 250 gms/ One Square Metre as per site condition on the surface to be treated with 10 cm overlapping including finishing etc. completeandcoveringguaranteeof7yearsonstamppaper ofRs. 100/-and asdirected by Engineer-in-charge. (Prior permission of S.E.in writing is necessary before inclusion of this item in estimate). | sqm | ₹ 678 |
| 51.115 | Providing and laying mechanical protective layer over water proofing membrane with cement screed plaster 1:5 after laying chicken mesh over membrane including curing etc. complete 20 mm thick with cost of chicken mesh etc. complete and covering 7 years guarantee on court stamp paper of Rs.100/- including necessary testing specified by Engineer (Prior permission of S.E. is necessary before inclusion of this item in estimate) (Note:- This item shall be executed over item One Number 5 of BD-J Water Proofing) | sqm | ₹ 390 |
| 51.116 | Providing and applying a Silicon Base Water Repellent Stone Sealers, on Brick / Stone masonry / Concrete surfaces in Two coats by spraying. Including cleaning / sand blasting for removing dirt / cement mortar patches etc. by force water jet, wire brushing etc. complete. | sqm | ₹ 557 |
| 51.117 | Providing internal / external 12 mm thick Ready Mix plaster confirming to IS:4031(Part- 4) 1988 and IS 383-1970 in a single coat using Cement mortar of proportion 1:4 containing special type of polymer additives about 0.4%, to all type of surfaces in all positions including scaffolding and curing complete. | sqm | ₹ 238 |
| 51.118 | Providing internal / external 20 mm thick Ready Mix plaster confirming to IS:4031(Part- 4) 1988 and IS 383-1970 in a single coat using Cement mortar of proportion 1:4 containing special type of polymer additives about 0.4%, to all type of surfaces in all positions including scaffolding and curing complete | sqm | ₹ 417 |
| 51.119 | Providing brick masonry with interlock "Fourlock" bricks in retaining walls,diaphragm wall,compound wall,plinth & partition wall etc of specified 150 mm thick including construction with interlock "Fourlock" brick, filling the hollow spaces with cementious grout material of proportion of C:M 1:6 using trap stone grit metal/artificial sand dusting off the finished brick masonry"Fourlock" bricks, surface,watering & curing etc complete. ( Including steel reinforcement of 8mm bar as strengthening bar in hollow spaces of fourlock bricks with cementious greet material) | sqm | ₹ 1,547 |
| 51.120 | Providing brick masonry with interlock "Fourlock" bricks in plinth & superstructure of specified 150 mm thick including construction with interlock "Fourlock"bricks,filling the hollow spaces with cementious grout material of proportion of C:M 1:6 using trap stone grit metal/artificial sand including dusting off the finished brick masonrysurface,watering & curing etc complete. ( Excluding steel reinforecement for strengthening) | sqm | ₹ 1,291 |
| 51.121 | Providing brick masonry with interlock "Fourlock" bricks in retaining walls,diaphragm wall,compound wall,plinth & partition wall etc of specified 100 mm thick including construction with interlock "Fourlock" brick, filling the hollow spaces with cementious grout material of proportion of C:M 1:6 using trap stone grit metal/artificial sand dusting off the finished brick masonry"Fourlock" bricks, surface,watering & curing etc complete. ( Including steel reinforcement of 8mm bar as strengthening bar in hollow spaces of fourlock bricks with cementious greet material) | sqm | ₹ 1,315 |
| 51.122 | Providing brick masonry with interlock "Fourlock" bricks in plinth & superstructure of specified 100 mm thick including construction with interlock "Fourlock"bricks,filling the hollow spaces with cementious grout material of proportion of C:M 1:6 using trap stone grit metal/artificial sand including dusting off the finished brick masonrysurface,watering & curing etc complete. ( Excluding steel reinforecement for strengthening) | sqm | ₹ 1,059 |
| 51.123 | Construction of M-40 grade reinforced prestressesd precast concrete panel of 200 mm thickness having size 4.5m x 3.5m or as per drawing, casting the panels as per approved design and drawing in factory or plant including cost of all materials, formwork, reinforcement, dowel bars, tie bars, chairs, lifting bolts, grout ports, labour and all necessary machineries which are required for prestressing the wires, preparing concrete mix as per job mix design (The minimum cement content for M40 grade of PPCP shall be 440 Kilogram/cum of concrete), making slots in panels for fixing dowel bars, tiebars, and placing necessary reinforcement as per design and drawing, steam/curing for 28 days including lifting, transportating and placing the panels at the required position, line, level and alignment as directed by Enginner in Charge, with max 20% fly Ash ( Fly-ash upto 20% by weight of Cement) over a prepared sub base. including providing and fixing in position MS Plain dowel bars precoated with anticorrosive epoxy paint of required Dia. having 45 cms. length and at 30.00 cm. c/c lubricated for half length with bituminous paint and providing & fixing TMT Fe 500 tie bars 12 mm dia. 60 cm long at 75 cm c/c, handling, straightening, necessary cutting supported by TMT FE 500, chairs with proper alignment by using properly designed assembly of Bulkheads. Including, Grouting of baseofthepanelsaswellasdowelandtieslots inthepanels, Providing contraction joints polysulphide sealent (Pouring grade) confirming to BS: 5212 - 1989 into groove of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter (appraox. 25% larger than the initial 3 mOne Metric Tonneo 4 mm. joint) overlaid with bond breaking tape as per detailed drawing. Item includes cleaning the joints with water jet / air compressor and allowing joint to become thoroughly dry before sealent is applied and applying primer.(A) Contraction and longitudinal joints (50 mm. deep x max. 6 mm wide) | cum | ₹ 16,589 |
| 51.124 | Providing andlaying ofPlastirib T or equivalent raised profileedge linemarking (audible vibratory) with special hot applied thermoplastic road marking compound according to IRC 35: 2015, Clause 7.7 with2 mm thick base coat layer above that ribs profile size of length 40 mm x width 140 mm x height 6mm thick (Total 8 mm thick) at the distance of 250 mm between two ribs including reflectorizing glass beads @ 250 gm / sq. mtr. area. The minimum and maximum width of raised profile should be 150 mm. The thickness of 8 mm profil should be exclusive of surface applied glass beads. The finished surface to be exclusive of surface applied glass beads. The finished surface to be levelled, uniform and free from streaks and holes, to be applied on edge lines. | sqm | ₹ 1,009 |
| 51.125 | Providing and laying of Plastirib 2K or equivalent raised profile edge line marking (audible vibratory) with special 2 component cold applied road marking compound according to IRC 35: 2015, Clause 7.7 with 2 mm thick base coat layer above that ribs profile size of length 40 mm x width 140 mm x height 6mm thick (Total 8 mm thick) at the distance of 500 mm between two ribs including reflectorizing glass beads @ 250 gm / sq. mtr. area. The minimum and maximum width of raised profile should be 150 mm. The thickness of 8 mm profil should be exclusive of surface applied glass beads. The finished surface to be exclusive of surface applied glass beads. The finished surface to be levelled, uniform and free from streaks and holes, to be applied on edge lines. | sqm | ₹ 2,629 |
| 51.126 | Providing and Laying of Rumble strips with Plastirib 2K, orequivalent 2component cold plastic profiled material to give total width of 500 mm and height of 10 mm. Ramp provided to give width of 145 mm, width of ribs to be 55mm laid at centre to centre distance of 35 mm, with reflective glass beads @ 350 gm / One Square Metre. The finished surface to be levelled, uniform and free from streaks and holes, to be applied on the edge lines, including surface cleaning and cost of all materials etc. complete. | sqm | ₹ 3,706 |
| 51.126 (2) | Providing and Laying of 2 or more sets (6 Nos. each set) Dual Ribs Pattern Rumble Markings on roads with vehicular speeds of more than 50 Km/hr laid as per the spacing recommended for each set under Table 11.1 and Fig. 11.2 of IRC 35:2015 using Plastirib 2K, or equivalent 2 component cold plastic profiled material. Each Dual Rib pattern rumble marking shall have width of 500 mm. Each dual rib pattern rumble marking shall have 2 ribs each of Width of 100 mm and height 20 mm. Gap between two ribs shall be 300 mm. Each rumble marking shall be made complete with drop on Soild Plus reflective glass beads@300gm/ OneSquareMetre spreadthroughout thesurface ofmarking. The finished surface to be levelled, uniform and free from streaks and holes, including surface cleaning and cost of all materials etc. complete. | sqm | ₹ 4,333 |
| 51.127 | Supplying and fixing of Plastic body studs with two shanks and without shanks of SWAREFLEX or equivalent in yellow, red and white color made of ABS body with size 100*100*17.9 mm, having reflective panels of 34 special Swaro glass reflective elements embedded in plastic and 19 degrees tilted to provide the highest reflectivity. Having reflective panels in yellow, red and white plastic with yellow, red, white or green Swaro glass elements. The studs shall have a compressive strength test certificate of 25 tons in accordance with ASTDM D 4280 and successfully passing retro reflectivity test as per EN 1463-1 and the road test EN 1463-2 from a reputed laboratory. The fixing of the road studs shall be done by using a recommended Two Component Epoxy. In addition two holes should be drilled in the depth of 50 mm on the road for the version with two shanks. | nos | ₹ 477 |
| 51.128 | Supplying and fixing of Swareflex or equivalent Metal Road studs with shank, made of Die-cast Aluminum alloy molded body with the size of 100*100*19.8 mm, shank size 50mm, having reflective panels of 34 glass reflective elements embeddedin plasticand 19 degrees tilted to provide the highest reflectivity having reflective panels in yellow, red and white plastic with yellow, red, white or green glass elements. The weight of Aluminum stud should be not less than 370 grams. The studs shall have a compressive strength test certificate of 40 tons in accordance with ASTDM D 4280-04 and successfully passing retro reflectivity test as per EN 1463 part 1 & part 2, from a reputed international laboratory. The bidder shall attach a product warranty certificate against Breakage and loss of reflectivity from the manufacturer for 3 years from installation. The fixing of road studs shall be done by using a recommended Two Component Epoxy after drilling 60 mm hole on the road for the shank to go inside. | nos | ₹ 562 |
| 51.129 | Supplying and fixing of Plastic body of Swaro Warn or equivalent 184*81*60 mm, mounted on road side plastic guide posts at a height of 80cm to 100cm from the ground level and fixed on post with screws supplied with the Swaro warn product. Swaro Warn comes in white or blue color. Visual wildlife warning system deflecting the headlights of approaching vehicle towards Road side at Dusk or night for creating a visual warning fence for the wildlife to avoid the accidents of wild life. Confirming standards RVS 04.03.12. The Swaro Warn article 7178 can be used for all types of terrain. | nos | ₹ 3,446 |
| 51.130 | Stabilization of Soil or Sub-Base/Base Course or Existing Pavement Crust upto the required depth by In-Situ Stabilization method using Cement / Cementitious additives / Chemical additives / Combination: Providing and pre-spreading of Binder (Cement / Cementitious additives / Chemical additives / combination) at rate of required quantity (% by weight) as per job mix design in accordance with IRC 37-2018 using a truck-mounted automated binder spreader with micro-processor controlled weighing and spreading system. The binder spreader shall have variable working width upto 2.4m to efficiently manage the width of the whole pavement. The in-situ stabilization process shall be carried out using a self-propelled wheeled Stabilizer / Reclaimer with a minimum working width of 2m or 2.4m and minimum engine horsepower of 305 kW havingin-built automated water-spraying anddepth control systems with variable working depth of up to 500 mm. The entire in-situ process shall be carried out in a single pass including pulverizing of soil/aggregates/combination or milling of existing asphalt pavement and simultaneous mixing with pre-spread binder (cement/additive) and water to the desired depth. Theresultant stabilized mixshallbe compacted using avibratorypadfoot compactor of14- 20 tonne weight as per design depth and then graded to the required profile, level and thickness using a motor grader. The graded surface shall be then compacted using a smooth vibratory roller to achieve the desired proctor density as per IRC 37-2018 and complete in all respects including curing with water as required including all materials, labor, machinery, etc. Necessary graded stone aggregates shall be added by pre-spreading with cement to achieve desired gradation and profile of the road. The minimum unconfined compresssive strength (UCS)ofstabilized sub-baseshould be4.5 / 7 MPaafter 7/ 28days curingas per IRC 37-2018.Also, durability aspects (wet-dry cycles) of stabilized sub base should be satisfied as per IRC 37-2018.The gradation mixes and materials should be as per IRC 37- 2018. | cum | ₹ 3,627 |
| 51.131 | Rehabilitation of existing damaged asphalt pavement by Cold In-Place Recycling (CIPR) process, using foamed bitumen as binder and cement as filler, as per IRC 120-2015 / IRC 37-2018: Providing a layer of fresh aggregates as per design mix byevenly pre-spreading on the exisiting damaged asphalt surface using paver or motor grader to achieve the desired gradation and profile of the road. 1% cement by weight of the mix shall be pre- spread on the layer of fresh aggregates using a truck-mounted automated binder spreader withmicro-processor controlledweighingandspreadingsystem. Thebinderspreader shall have variable working width upto 2.4m to efficiently manage the width of the whole pavement. The pre-spread fresh aggregates and cement and the existing damaged pavement shall be then pulverized and recycled in-situ up to design depth by injecting 2- 2.5% bitumen (VG30) as foamed bitumen as per design mix using a self-propelled wheeled Recycler equipment with a minimum working width of 2m or 2.4m and minimum engine horsepower of 305 kW. The Recycler equipment should have in-built automated water-spraying system and temperature-controlled foamed bitumen injection system with variable and controlled working depth of up to 500 mm. The entire in-situ recycling process shall be carried out in a single pass including milling and pulverizing of existing asphalt pavement with pre-spread aggregate and cement up to desired depth and simultaneous injection of foamed bitumen and water as per job mix design.The resultant recycled mix should be then compacted to required density using 14-20 tonne vibratory padfoot compactor as per design depth; profiled by motor grader and further compacted by smooth vibratory roller and PTR and complete in all respects as required including all materials, labor, machinery, etc. (This cold recycled surface shall be then covered with tack coat and bituminous concrete of 50mm thickness, cost of both to be accounted separately) | cum | ₹ 7,370 |
| 51.132 | Providing and erecting a Road Restraint system - Roller System Barrier ETI Roller System H1 & H2 comprisiong of post of hot dip galvanized steel of139.8mm diameter(L- 2200 and L-750) thickness 4.5 mm spaced with interval of 1 meter installed in to hardened road. Safety frame rail from sheet of 3.20mm thick are fixed to main posts, shock absorbing rollers 345 mm diameter and 480mm height made of polypropelene - EVA, post caps, locker, pipes and connection material. Distance between main post and short post shall be 500 mm. the height of upper edge rail is 960 mm. All steel parts( FRAME s235R equivalent SS400) and post S235JR shall be hot dip galvanised to protect against corrosion. The system shall be installed in accordance with the drawings and assembly instructions. etc. complete. | rmt | ₹ 74,511 |
| 51.133 | Providing and laying Stone Matrix Asphalt with 100-120 TPH batch type hot mix plant producing an average output of 75 tonne per hour using crushed aggregate of specified grading premixed with bituminous binder @ 5.80 minimum percent of mix and filler, transporting the hot mix towards site, laying with hydrostatic paver finisher with sensor control to required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause One Number515 etch. complete in all respects, IRC SP 79 | cum | ₹ 11,689 |
| 51.134 | Milling of existing bituminous surface to specified depth of bituminous layer including disposal of removed material with all lift and lead upto 1000 m etc complete. Using machine like Writgen (W100) or equivalent | sqm | ₹ 44 |
| 51.135 | Providing and applying low viscositybitumen emulsion RS1 for sealingcracks less than 3 mm wide or incipient fretting or disintegration in an existing bituminous surfacing. | sqm | ₹ 38 |
| 51.136 | Providing and laying Microsurfacing course comprising of dry (A) fine aggreegates confirming to Type III grading @12 Kilogram/ One Square Metre. of Road Surface coverageofspecification asperIRC SP 81, 2008Polymer / latest modifiedcationic quick setting bitumen emulsion having 60% binder content and 3.6% polymer (B) @ 12.5% by weight of fine aggregate ordinary portland cement (C) @ 2% by weight of agrregate chemical additives (D) @1.5% by weight of fine aggregate and water as per requirement. | sqm | ₹ 179 |
| 51.137 | Providing and laying a Stress Absorbing Membrane Interlayer (SAMI) / bitumen impregnated geotextile layer after cleaning the road surface, geotextile conforming to requirements of clause 703.3, laid over a tack coat with 1.05Kilogramper One Square Metre of paving grade bitumen 80 - 100 penetration / emulsion as per requirement and as directed by Engineer in Charge. Pot Hole filling with Jet Patcher-Repairs to potholes 50 mm upto 100 mm by using semidense bituminous concrete in cold mix by using emulsion including making the potholes /patches in regular shape and size. Removing loose pockets, Dewatering in potholes,tack coats of 25 Kilogram/10 Sq.Mt.with RS1 emulsion etc.by use of advanced jetpatching technolgy machine of approved make and specification having capacity 5.50 TO 8.00 cubic meters with auxillaryenginewith direct drive toheavydutyblower, Rotary Positive Displacement Blower with direct drive and separate airline silencer. (Capacity – 15 PSI, Flow rate 1370/cum/hr). cleaning as directed by Engineer – in-Charge etc. complete (Emulsion @ 5% by weight of mix) | sqm | ₹ 125 |
| 51.138a | Upto 50mm | sqm | ₹ 1,317 |
| 51.138b | 50mm-100mm | sqm | ₹ 1,867 |
| 51.139 | Open Graded Premix Surfacing- Providing and Laying OGC 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates premixed with bituminous binder transported to site with VTS, laid over a previously prepared surface, finished to the required grade, level, alignment, and rolling to achieve the desired compaction but excluding prime / tack and Seal coat. For Bitumen of specified grade--USING Batch mix type hot mix plant with SCADA, Paver and Vibratory roller( over BT Surface) (VG-30 bulk bitumen rates are considered to arrive at rates) | sqm | ₹ 191 |
| 51.139 (2) | Open Graded Premix Surfacing- Providing and Laying OGC 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates premixed with bituminous binder transported to site with VTS, laid over a previously prepared surface, finished to the required grade, level, alignment, and rolling to achieve the desired compaction but excluding prime / tack and Seal coat. For Bitumen of specified grade--USING Batch mix type hot mix plant with SCADA, Paver and Vibratory roller ( Over MPM Surface) (VG-30 bulk bitumen rates are considered to arrive at rates) | sqm | ₹ 198 |
| 51.140 | Chipping of all loose and Spalling of concrete to bottom of slab, beams etc.(wherever required), cleaning of reinforcement, carrying out thorough sand blasting, application of anti-corrosive zinc rich epoxyprimer to exposed reinforcement including cost of material, labour, equipment, tools, scaffolding etc. complete. | sqm | ₹ 515 |
| 51.141 | Providing and applying epoxy bonding agent for bonding old to new concrete for structural members prior applying the epoxy mortar to the concrete surfaces etc complete. | sqm | ₹ 516 |
| 51.142 | Providing and applying epoxy mortar of resin and hardner with Sillica sand upto 20 mm thickness of Sika/Fosroc/Pidilite or its equivalent including proper wire brushing etc complete as per the direction of Site-In-Charge. | sqm | ₹ 4,858 |
| 51.143 | Charges for groove cutting of15 mm x 15 mm deep along crack and sealing and refilling the same with epoxy mortar including cost of material, labour etc. complete | rmt | ₹ 459 |
| 51.144 | Cleaning of rocker & roller bearing using high pressure water jet, free from rust scales, re- setting & greasing the bearings using graphite grease including cost of materials, labour etc., complete. | Per bearing | ₹ 9,335 |
| 51.145 | Bearing cleaning and pier cap cleaning for the proper movement of bearing etc. complete including all tools and machineries scaffolding etc.complete asper thedirection ofSite in Charge. | nos | ₹ 9,605 |
| 51.146 | Providing and applying “high strength, non shrink free flow grout material” i. e. micro concrete (like shrink comp or equivalent) having compressive strength as 400 Kilogram/sq.cm. includingfinishing thesurfaceand curingfor 07days. Etccomplete. The usage of this non shrink concrete with zero slump is to allow to occupy every free space leaving no voids, thereby producing dense concrete with proper bonding with concrete (The quoted rates to be inclusive of all materials, labours, tools & tackles, transportation, taxes etc complete) to be applied for foundation and strengthening of pier etc and as per the direction of Site-In-Charge. (The product like Ultratech/Rendroc (RGL) of FOSROC or its equivalent) | cum | ₹ 67,000 |
| 51.147 | Providing applying Polymer modified cement mortar pointing to the stone massonry structure including chipping, cleaning, applying bonding agent, stagging, curing and and all tools and tackes including safety etc. complete. | sqm | ₹ 1,435 |
| 51.148 | Grouting to the Dowel bars with epoxy of resin+hardner to ensure the proper fixing of dowel bars including all the machineries etc. complete, as per the direction of Site- In- Charge. | nos | ₹ 429 |
| 51.149 | Providing and applying waterfroof coating to the concrete surface to resist entry of moisture and prevent growth of fungus etc. complete as per the direction of site in charge. | sqm | ₹ 97 |
| 51.150 | Lifting of span and bearing locations by suitable hydraulic jacks connected by high pressure, rubber hoses to pump & removal of old exsting bearing ( Roller side only) As per Quotation | One Span | ₹ 176,233 |
| 51.151 | Strengthening structural elements by providing & fixing CARBON FIBER (Make Sika or BASF or FOSROC) Surface preparation: Grinding concrete substrate, cleaning it with wire brush removing oil, laitance if present, rounding sharp edges to min 25 mm radius etc. complete.Profiling: providing & Applying compatible Mbrace primer on prepared substrate, Filling the holes and uneven surface with high strength epoxy putty etc. complete IF Required. Wrapping: Providing & Applying first coat of Saturant, cutting the carbon fiber sheet to size, wrapping the fiber sheet to structural element at desired orientation using tamping roller to avoid any air voids etc. complete.Sand pasting: Providing & Applying second coat of Saturant after min. 12 hrs, rectify air voids if any paste the rive sand on it to make surface rough to take any further finishes(Mode of measurement: Per sq.mt of Mbrace CF 400 sheet applied and not surface area of Concrete application & Quantity will be measured including wastage) The rate includes all type of material,application,equipment & scaffolding etc complete. Rate is applicable for all height & level. | sqm | ₹ 6,260 |
| 51.152 | Replacement of existing damaged Expansion joints by providing and laying of Strip Seal Expansion Joint System, includingremoval ofexisting damaged exp joints bydismantling of deck slab, wearing coat etc. and back filling of the recess up to final finish level with conc of grade M-35, complete as per M.O.R. T&H specification. | rmt | ₹ 19,016 |
| 51.153 | Providing Polymer modified cement Mortar treatment after removing of existing, clading, plaster, gunite & cleaning and preparing the surface.Applying Polymer cement bond coat andPolymermodifiedcement Mortar asper manufacturerspecification upto 50mm thick with 8% polymer by weight of cement to fill the all cavities & making protective cover plaster including shuttering | sqm | ₹ 6,345 |
| 51.154 | Providing, drilling and fixing Nipples for pressure injection grouting of polymer cement grout etc. complete | nos | ₹ 266 |
| 51.155 | Filling voids/honeycomb with high pressure injection grouting of Polymer Cement Grout (10% of Polymer by Weight of Cement) | kg | ₹ 219 |
| 51.156 | Providing and laying in situ / ready mix M35 grade RCC jacketing work around the existing piers of bridges etc. complete. (with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant / pan mixer with fine agreegates of required specifications ( VSI sand finely washed etc), height of 8 to 10 meter) | nos | ₹ 9,280 |
| 51.157 | A) Precast BeB Panals 1 Providing and fixing Precast M 25 grade Concrete curved section of 100 mm thick to serve as bandhara as per the standard drawing approved by department having elliptical shape with base upto 6m as per table attatched to be casted in factory in suitable sections and transporting to site and erecting the same including all leads, lifts, labour and machinaries with finishing.One Number of elements in which compled section is proposed to be cast shall be approved.Necessary equipments for placing giving support through turn bucle or similar arrangement to maintain its verticality till insitu joining..The total steel quantity is 75Kilogram per cubic meter of concrete The method statement shall be prepared and got approved from engineer including cost of plasticizer and viscocity admixure. | sqm | ₹ 2,967 |
| 51.158 | b) Hot Dip Galvanised Needle Gate 1 Manufacturing with OAP &fabrication ofhot dipgalvanised needlegates -curved type of required size and Weight as per the detailed design and drawings with all material, Mild steel confirming to IS 2062, Rubber seal confirming to IS 4623 & Welding electrodes AWS E6013 for general weld joints. It includes all materials, Labour charges, machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting,overhead charges of10%, andallincidentialcharges includingallduties, taxes, levies andinsurance charges excludung GST | MT | ₹ 166,000 |
| 51.159 | Providing and fabricating and fixing at site hot dip galavanised structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted I bolted Iwelded connections without connecting plates, braces etc. complete including all transporation, labour and all lift excluding GST | MT | ₹ 110,000 |
| 51.160 | c) FRP Needle Gate 1 Providing, supplying and fixing of FRP gates -needles in curved or straight shape in size required size and 60mm thick for the Bridge -cum- Bandhara.The gate/needles should withstand under minimum water pressure of 7.00 tonne. with interlocking arrangements, required rubber seals to arrest water leakage due to surface unevenness including FRP "C" channels at both side of gate of size 100 mm x 100 mm with 10 mm thick, with lifting eye bolts. And as per specifications mentioned in the Technical spectications and product features excluding GST | sqm | ₹ 18,340 |
| 51.161 | Providing and fixing Sill beam in size 100 X100 mm with 10 mm thick, in FRP material with lifting eye bolts. And as per specifications mentioned in the Technical spectications and product features excluding GST | rmt | ₹ 2,500 |
| 51.162 | Supply and installation of cubicles of width and depth as per Athena Lite- SS Series Cubicles- Std Sizes (W x D x H): 900 mm x 1550 mm x 2105 mm, (Height is including 100 mm gap from bottom, Door Width- 600 mm specifications/ site drawings). Cubicle height to be 2105 mm. Made from solid grade compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure > 5 MPa and temperature >120°C, All doors will be of single colour and made of 12 mm thick Merino HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 stainless steel made hinges affixed to the pilasters. Size of panels to be as per drawing. HARDWARE & ACCESSORIES are H shaped (Top) head frame structure made of extruded Aluminium grade 6063 T5-50 micron epoxy powder coated for surface protection, Size to be 125x70x5T. Corner joinery section, Size to be 40x16.5x1.8T. U- Channel Wall joinery section,Size to be 22x16x1.6T. Door stopper section, Size to be 21x12.5x1.6T. Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacor coated.etc complete. | sqm | ₹ 11,196 |
| 51.163 | Supply and installation of CEILING HUNG cubicles of width and depth as per specifications/ site drawings. Cubicle height to be 2400 mm. Std Sizes (W x D x H): 900 mm x 1550 mm x 2400 mm, (Height is including 100 mm gap from bottom) Door Width- 600 mmITEM DESCRIPTION Made from solid grade Merino make compact high pressure laminate as per IS:2046 and EN 438manufactured underhigh specificpressure > 5 MPa and temperature >120° C, All doors will be of single colour and made of 18 mm thick Merino HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 stainless steel made hinges affixed to the pilasters. All intermediate partitions or dividers will be made of 12 mm thick Merino HPL compact laminate panels. Sizeofpanelstobeasperdrawing. HARDWARE& ACCESSORIES are Hshaped (Top) head frame structure made of extruded Aluminum grade 6063 T5-50 micron epoxy powder coated for surface protection. Size to be 125x70x5T. Corner joinerysection, Size to be 40x16.5x1.8T. U-Channel Wall joinery section, Size to be 22x16x1.6T. Door stopper section, Size to be 21x12.5x1.6T. Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacor coated.Coat hook with rubber stopper made from Stainless steel grade 304. Surface finish to be matt type. etc complete. | sqm | ₹ 9,051 |
| 51.164 | Supply and installation of PD DOOR cubicles of width and depth as per specifications/ site drawings. PD Door height to be 1980/2100 mm.PD Doors Series: Std Sizes (W x H): 2100 mm x 7500 mm (Height is including 150 mm gap from bottom), Door Made from solid grade Merino Make compact high pressure laminate as per IS:2046 manufactured under high specific pressure > 5 MPa and temperature >120°C,.Panel thickness 12 mm. Size of panels to be as per drawing. HARDWARE & ACCESSORIES are Specially designed D-shape wall mounted pole made from extruded grade aluminum alloy 6063/HE9/T-6 and epoxy powder coated (color as per specifications) for surface protection. Size to be 46x41x2T, Matching profile and color Nylon Polyamide-6 caps to cover aluminum Poles, Self closing Hinges (Gravity mechanism) made from Nylon Polyamide grade-6. Color to be as per specifications, Stainless steel grade 304 screws, Anti-rotation Nylon polyamide grade-6 expandable wall plugs, etc complete. | sqm | ₹ 8,762 |
| 51.165 | Supply and installation of 12MM BOX UP cubicles of width and depth as per specifications/ site drawings. Cubicle height to be 2100Titan Box up 18 mm Series Cubicles: Std Sizes (W x D x H)- 900 mm x 1550 mm x 2100 mm, (Height is including 100 mm gap from bottom) Door Size- 600 mm mOne Metric Tonneitan Box up 18 mm Series Cubicles: Std Sizes (W x D x H)- 900 mm x 1550 mm x 2100 mm, (Height is including 100 mm gap from bottom) Door Size- 600 mmTitan Box up 18 mm Series Cubicles: Std Sizes (W x D x H)- 900 mm x 1550 mm x 2100 mm, (Height is including 100 mm gap from bottom) Door Size- 600 mmITEM DESCRIPTION: Made from solid grade Merino make compact high pressure laminate as per IS:2046 manufactured under high specific pressure > 5 MPa and temperature >120°C, All doors will be of single colour and made of 18 mm thick Merino HPL compact panel. All pilasters will be made of 18 mm thick Merino HPL compact panel. HARDWARE & ACCESSORIES are No head frame structure, all panels to be aliengned to the top, Corner joinery section made from Stainless steel grade 304. Surface finish to be brush type. A thin plastic film pasted for surface protection. Size to be 35mmx15mmx0.8 mm. etc complete. | sqm | ₹ 8,634 |
| 51.166 | Supply and installation of cubicles of width and depth as per specifications/ site drawings. Cubicle height will be 1980 mmTitan Std Series Cubicles: Std Sizes (W x D x H): 900 mm x 1550 mm x 1980 mm/2039 mm ( Height is including 150 mm gap from bottom) Door Size- 600 mm when top rail of rectangular cross section is used and 2039 mmwhen toprailofcircularcross section is usedITEMDESCRIPTION Madefrom solid grade Merino make compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure > 5 MPa and temperature >120°C, All doors will be of single colour and made of 12 mm thick Merino HPL compact panel. All pilasters will be made of 12 mm thick HPL compact panel. Size of panels to be as per drawing. HARDWARE & ACCESSORIES are Top rail is made of stainless steel grade 304. There are two options for the top rail. First one comes with a rectangular cross section (Size to be 55mmx42mmx1.6 mmT) and the other one comes with circular cross section (Diameter 32 mm). Surface finish to be brush type. A thin plastic film pasted for surface protection. Corner joinery section made from Stainless steel grade 304. Surface finish to be brush type. A thin plastic film pasted for surface protection. Size to be 35mmx15mmx0.8 mm. etc complete. | sqm | ₹ 8,324 |
| 51.167 | Supply and installation of ZMS (Nylon) cubicles of width and depth as per specifications/ sitedrawings. Cubicleheight willbe2003mm.ZMS Series Cubicles: StdSizes (W xD x H):900 mmx1550 mmx 2003mm, (Height is including150 mmgap frombottom) Door Width- 600 mmITEM DESCRIPTION Made from solid grade compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure > 5 MPa andtemperature>120°C.Alldoorswillbeof singlecolour and made of12 mmthick HPL compact panel. All pilasters will be made of 12 mm thick HPL compact panel. All intermediate partitions or dividers will be made of 12 mm thick HPL compact laminate panels. Size of panels to be as per drawing. HARDWARE & ACCESSORIES are Semi- spherical (Top) head frame structure for surface protection. Size to be 50x32x1.6T. Corner joinery section, Size to be 40x16.5x1.8T.U-Channel Wall joinery section, Size to be 22x16x1.6T.Door stopper section, Size to be 21x12.5x1.6T. Stainless steel grade 304 screws, Anti-rotation Nylon polyamide grade-6 expandable wall plugs, The Work shall complete as per drawing, under supervision of engineer in charge, etc complete. | sqm | ₹ 5,909 |
| 51.168 | Steel Fiber Reinforcement: Supplying, Providing and Mixing Hooked End/Crimped steel fibers with aspect ratio between 50 to 80 (Diameter between 0.45 to 01mm and length between 12.5 to 60mm) manufactured from cold drawn wire and having a minimum tensile strength of 1100N/Sq.mm, as per CE Certification label mark, HE non-glued/ HE glued, non-balling, conforming to ASTM A 820 /EN 14889-1, compatible with all construction chemicals used for the batching, laying and curing of concrete. The fibers shall be added to the concrete at specified dosage and shall be mixed with the concrete ingredients for sufficient time to ensure uniform distribution and pumping concrete. Addition of steel fibers in cement concrete for flooring/ pavement/CC roads (All ground supported slab)/underground structure/precast items (like drains, manhole covers, walls, paver blocks, pipes, tunnel segments) etc. doses as per approved designs and directions of Engineer-in-Charge. HSN Code for Steel Fibres is 73170013. Regularly used are MSCF 50; MSH 10050; MSH 7560; MSH7035; MSH 6035; MSH 5530; NSH-G 7560; MSH-G 7035; MSH-G 6035; MSH-G 5530 etc. are some of the widely used sizes. | kg | ₹ 112 |
| 51.169 | Fire Door 55mm 2HR FRL (120/120) 3 Criteria - INTEGRITY / INSULATION/ STABILITY WOODEN DOOR - Fire Door Tested in accordance to IS: 3614 Part 2. Providing of 120 min Fire rated doors system duly tested for 3 criteria - Integrity, Insulation and StabilityCriteria as per the IS: 3614 Part 2 and BS: 476 part 22 at National Test House, Govt of India laborator and/or with Central Building Research Institute, Govt of India undertaking with standard heating conditions as specified in IS:3614 Part II 1992 and BS: 476 part 20 & 22 1987 to achieve the required integrity, insulation and stability (i.e. to restrict the heat radiation, temperature rise on the non fire side to the maximum of 140° C above the ambient temperature on the exposed surface of the shutter. The fire doors are tested with NCBN technology ("Non Combustible by Nature"). | ||
| 51.169a | Door Frame: Supplying & Fixing frames for Fire resistant door shutters 1st class Malaysian Hardwood Frame densified (810 Kilogram/cum) and pressure treated with fire retardant chemicals in vacuum impregnation vessel under 160 psi pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 of section 120 X 70 mm spray quoted with 2 coats of intumescent paint of minimum 200 micron, with single row of Brush- Type ASTROFLAME intumescent strip of size 10mm x 4mm affixed in the slit of the Frame for fire and smoke sealing, etc. complete. | rmt | ₹ 1,839 |
| 51.170 | b)Shutter: Supplying & Fixing of 55mm thick asbestos free criteria checked - fire, heat and smoke resistant composite Fire check Door Shutter complying with with fire performance - FD 120 as per IS:3614 (part - II) comprising of 2x8mm Calcium Silicate boards over Chemically treated (with Fire retardant chemicals in vaccum pressure impregnation vessels under 160 psi pressure as per IS:401 and kiln seasoned to moisture below 15% as per IS:1141) internal timber (Malaysian Hard Wood, densified to 810 Kilogram/cum) frame work of 100x32 mm with 32mm thick infill of ceramic fiber (density 128 Kilogram/cum), vermaculite mix faced with 3mm Fire retardant High Density fibre board, internally lipped with hardwood beading and pasted in Hydraulic Press under 25 MPa, spray quoted with 2 coats of in-tumescent paint of minimum 300 micron, and with single row of Brush-Type intumescent strip of size 10mmx4mm affixed on periphery for fire and smoke sealing in the slit on all edges of shutter except bottom, without any external lipping. | sqm | ₹ 10,604 |
| 51.171 | c) Vision Panel: 2 HR rated E Class clear high stress fire rated glass is pre fabricated strategically inside the shutter structure with 10 mm inside the shutter on all sides with U- glazing. An additional insulated powdercoated 'Z' channel of 16 swg MS sheet to be fixed for reinforcement of the joints. Providing of 2 Hour Rated Acoustic Fire Door to effectively control noise in conference rooms, broadcasting studios, theatres andmusicpracticerooms. dulytested for 3criteria - Integrity, Insulation and Stability Criteria as per the IS: 3614 Part 2 and BS: 476 part 22 with standard heating conditions as specified in IS:3614 Part II 1992 and BS: 476 part 20 & 22 1987 to achieve the required integrity, insulation and stability (i.e. to restrict the heat radiation, temperature rise on the non fire side to the maximum of 140° C above the ambient temperature on the exposed surface of the shutter. The accoustic fire doors are tested with NCBN technology ("Non Combustible by Nature") duly tested for sound insulation as per ISO 10140-2 / ASTM E 90 for sound transmission loss evaluation of 42db in reverberation chamber at ARAI. | sqm | ₹ 57,157 |
| 51.172 | a)Door Frame: Providing & Fixing Frames for Fire resistant door shutters 1st class Malaysian Hardwood Frame densified and pressure treated with fire retardant chemicals in vacuum impregnation vessel under 160 PSI pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 of section 120 X 70 mm sprayquoted with 2 coats of In tumescent paint of minimum 200 micron, with 1 row of Brush- Type Astroflame® intumescent strip (imported) of size 10mmx4mmconcealed inthe grooveof theFrame for fire and smoke sealing, etc. complete as per direction of Engineer in Charge | rmt | ₹ 1,936 |
| 51.173 | b)Shutter:Supplying&Fixingof75mmthick asbestos free, fire,heat andsmoke resistant composite Acoustic Door Shutter complying with with fire performance - FD 120 as per IS:3614 (part - II) comprising of 2x12mm Calcium Silicate boards over Chemically treated (with Fire retardant chemicals in vaccum pressure impregnation vessels under 160 psi pressure as per IS:401 and kiln seasoned to moisture below 15% as per IS:1141) internal timber (Malaysian Hard Wood, densified to 810 Kilogram/cum) frame work of 100x36 mm with 36mm thick infill of ceramic fiber (density 128 Kilogram/cum), vermaculite mix faced with 6mm Fire retardant High Density fibre ply, internally lipped with hardwood beading and pasted in Hydraulic Press under 25 MPa, sprayquoted with 2 coats of in-tumescent paint of minimum 300 micron, and with single row of Brush- Type intumescent strip of size 10mmx4mm affixed on periphery for fire and smoke sealing in the slit on all edges of shutter except bottom and placement of 3 mm thick rubber membrane, at the inside face, sandwitched between calcium silicate board & high density fire retardant ply, without any external lipping with triple rebatting in shutters, etc complete. Providing of Fire Barrier Systems to prevent the spread of fire and smoke within roof and ceiling voids. | sqm | ₹ 15,374 |
| 51.174 | Fire Barrier: Providing 100mm thick asbestos free composite - 3 criteria - fire, heat and smoke check Fire Barrier to prevent the spread of fire and smoke within roof and ceiling voids with flame guard of 120 minutes as per IS: 3614 part -II comprising of 4 x 12mm thick Calcium Silicate boards, Chemical treated internal timber with Fire retardant chemicals in pressure impregnation vessels under 160 PSI pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 frame work of 50mm x 100 mm with 50mm thick infill of ceramic fiber (density 96Kilograms/CMT), vermaculite mix reinforced by MS 8mm bars supported within the existing structure & sealed with fire retardant Poly Urethane foam. All emptyspaces will be filled with ceremic wool as per instruction of the engineer. | sqm | ₹ 10,453 |
| 51.175 | Panic Bar: (For 2 Hr fire Rated single Panic bar) Supplying, fitting & fixing Surface mounted Crash Bar/ panic Bar of touch pad style,made of heavy duty cast iron/ steel body & latches with SS,BHMA certified & conforming to ANSI A 156.3 for grade-1 ( 3 hours fire rated) and suitable for surface mounting to wooden/hollow metal/ Al framed door,with maximum operating force 8Kilogram for unlocking easily & outwardly during emergency,complete in all respect as perdirection &satisfaction ofEngineer-in chargeincluding alltaxes &incidental charges. (Note: To be installed at "FIRE EXIT"only under location specific instruction of Eingineer-in -Charge.) | nos | ₹ 10,189 |
| 51.176 | Door Closure: (For 2 Hr fire Rated EN-3 Door Closure) Supplying, fitting & fixing Surface mounted overhead Door Closer for 2 hour fire rated doors of different size (e.g size -EN-3 for leaf widthupto 900mm)CE certified, marked & conforming to EN - 1154 of approved quality (Internationally reputed brand like Dorma, Geze, Hafele, Assabloy & Magnum etc.) fitted and fixed Complete as per direction & satisfaction of Engineer -in Charge including all taxes & incidental charges. | nos | ₹ 3,908 |
| 51.177 | 12"SS Handle: (For 2 Hr fire Rated 12"SS Handle) Supplying, fitting & fixing Stainless Steel 'D'or 'H'type of size 300 mm x 19 mm tubular Handle with Grade 304, CE certified, marked & conforming to EN - 1154 of approved quality (Internationally reputed brand like Dorma, Geze, Hafele, Assabloy & Magnum etc.)as per direction of Eingineer -in Charge fitted and fixed complete including all taxes & incidental charges. | nos | ₹ 2,041 |
| 51.178 | Providing and laying White Topping as per IRC-SP 76-2015 over bituminous surface (Existing bituminous surface preparation to be done if necessary either by milling or levelling course with BM/DLC to correct surface profile and to be paid separately) with unreinforced M-40 grade Pavement Quality Concrete using Ordinary Portland Cement (OPC 43/OPC 53-Grade) at 357kg/cum and 105 kgs of Fly Ash (Replacement of Fly Ash to the extent of 15% and Fine aggregate by 10%) coarse aggregate, fine aggregate and Admixture confirming to IS 9130-1999 (R-2004) polymeric synthetic fibre as per ASTM (1116) such as polyester / polyethylene / polypropylene / Glass fibre at 1.20 kg/cum, mixed in batching and mixing plant or weigh batcher as per approved mix design to achieve minimum flexural strength ormodulus ofrupture ofconcrete 4.50MPa at 28 days limiting maximum water cement ratio to 0.40, transported to site, laid with mechanical paver finisher, spread, vibrated, compacted and finished in a continuous operation to the lines and grades as per drawing, texture finishing of surface, spraying two layersof curing compound, curing with water sprayed on hessian cloth covered over concrete surface, groove cutting grid 1m x 1m to a depth of 1/3 of the Thickness and of width 3-5 mm as per design including cost of all material, side form work, sealing joints labour and HOM of machineries etc. complete as per specifications.. | cum | ₹ 7,424 |
| 51.179 | Standard Metal Delineator Supply and Installation of Road delienators ( Road way Delienators) as per MORT&H clause 806.The structure shall be manufactured in roll forming process and shall have height not less than 800 mm above the ground, width not less than 100 mm and shall extend not more than 300mm below the ground while being installed inconfirmation with IRC:79 1981or as directed by engineer in charge.The delineator shall be painted with powder coat of minimum 40 microns thickness for protection against corrosion, on top of which Type XIretro reflective sheeting shallbe pastedon both sides. Thedelienator shall consist minimum retro reflective unit exposed area of 330 cm2 white color, full cube cornermicroprismaticnon-metallicretroreflectivesheeting oneach sideconforming with IRC 67 2012 and meeting the coefficient of retro reflection values as per ASTM D 4956 Type XI table specification.The front and back faces of the delineator should be curved with a radius of not more than 200 mm and with delta angle (or central angle of curve) lying between 20o and 30o, to increase the visibilityof the delineator for vehicles moving in continuous curves. The delineator shall have grooves across the length to make the reflective sheets vandal-proof. | nos | ₹ 1,352 |
| 51.180 | Flexible Median Marker Supply and Fixing of Flexible Median Marker which shall be made of tough, high impact resistant, injection-molded, thermoplastic bodywith U shape structure with overall height of minimum 180mm and shank depth of minimum 30mm and thickness not less than 2mm. The exposed body structure should be cornered rounded for better aesthetics. The plastics used for the molding the flexible median marker shall have a minimum notched Izod Impact strength valueof 4.11J/cm(@thickness 3.17mm)at roomtemperature, tested in accordance with ASTM D256. The outer part of the body shall have the Abrasion loss not less than 35 mm3 when tested accordance with DIN53505 andDIN53516 respectively and shall retain at least 70% of this value when it is subjected to accelerated weathering for 500hrs as per the ASTM G155 standard.. The logo of the manufacturer shall be embossed on either side of the body in the injection molding process. - The flexible median marker shall have U shaped florescent yellow color retro-reflective sheeting with minimum exposed reflective area 285 mm2. The reflective sheeting should confirm to Type XI Florescent Yellow sheeting as per IRC 67 2012 and ASTM D4956-11. The product design has to with stand all natural impacts and should not get damaged if any pedestrian stamp on top of it intentionally or unintentionally. The product should bend up to 90 degree on both sides (becoming completely horizontal), it should be able to take minimum 200 stamping without any significant damage. The Flexible Median Marker shall be fixed by a combination of epoxy adhesive and grouting/Drilling as per Engineer IN Charge | nos | ₹ 405 |
| 51.181 | BITUMNOUS CONCRETE:- Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with HIMAGrade bituminous binder like ART (HighlyModified Asphalt Binder having not less than 90°C Softening Point and not less than 90% Elastic Recovery) @ 5.4% (percentage by weight of total mix) and lime filler @ 2% (percentage byweight of Aggregate) prepeared in Batch Type Hot Mix Plant and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratoryand tandemrollers toachieve thedesired 40/50mm compacted thickness and density as per specification, complete and as per directions of Engineer-in- Charge. | cum | ₹ 12,770 |
| 51.182 | Providing, Supplying, Laying & Fixing of concrete Canvas 5mm thick (flexible concrete impregnated fabirc which hardens when hydrated to form thin, durble, water proof & fire resitant concrete layer within 24 hrs) for slope protection/drain lining/concrete repair works and other similar works complete in all respect and as per direction of engineer-in- charge. Special Condition 1) Contractor shall submit all relevant test certificates of the material. 2) Mass of unset concrete canvas should be 7Kilogram/ One Square Metre. 3) Width of roll should be 1 m. | sqm | ₹ 4,404 |
| 51.183 | Providing, Supplying, Laying & Fixing of concrete Canvas 8mm thick (flexible concrete impregnated fabirc which hardens when hydrated to form thin, durble, water proof & fire resitant concrete layer within 24hrs) for slop protecion/drain lining/concrete repair works and other similar works complete in all respect and as per direction of engineer-in-charge. Special Condition 1) Contractor shall submit all relevant test certificates of the material. 2) Mass of unset concrete canvas should be 12Kilogram/ One Square Metre. 3) Width of roll should be 1.1m. | sqm | ₹ 6,153 |
| 51.184 | Providing, Supplying, Laying & Fixing of concrete Canvas 13mm thick (flexible concrete impregnated fabirc which hardens when hydrated to form thin, durble, water proof & fire resitant concrete layer within 24hrs) for slopw protecion/drain lining/concrete repair works and other similar works complete in all respect and as per direction of engineer-in- charge. Special Condition 1) Contractor shall submit all relevant test certificates of the material. 2) Mass of unset concrete canvas should be 19Kilogram/ One Square Metre. 3) Width of roll should be 1.1m. | sqm | ₹ 7,695 |
| 51.185 | Providing, Supplying, Laying & Fixing of concrete Canvas hydro 5mm thick (flexible concrete impregnated fabirc which hardens when hydrated to form thin, durble, water proof & fire resitant concrete layerwithin 24hrs)for slopwprotecion/drain lining/concrete repair works and other similar works complete in all respect and as per direction of engineer-in-charge. Special Condition 1) Contractor shall submit all relevant test certificates of the material. 2) Mass of unset concrete canvas should be 8Kilogram/ One Square Metre. 3) Width of roll should be 1m. | sqm | ₹ 6,452 |
| 51.186 | Providing, Supplying, Laying & Fixing of concrete Canvas hydro 8mm thick (flexible concrete impregnated fabirc which hardens when hydrated to form thin, durble, water proof & fire resitant concrete layerwithin 24hrs)for slopwprotecion/drain lining/concrete repair works and other similar works complete in all respect and as per direction of engineer-in-charge. Special Condition 1) Contractor shall submit all relevant test certificates of the material. 2) Mass of unset concrete canvas should be 13Kilogram/ One Square Metre. 3) Width of roll should be 1m. | sqm | ₹ 11,066 |
| 51.187 | Supply and Installation of translucent roof with DPI Flux standing seam multicell polycarbonate panel system. The system with complete assembly of co extruded UV protected multicell panels incorporated intoa completesystem. Co-extruded UV protected polycarbonate panel system of min 12 mm thick of 900 mm (min.) width with angular daylighting concept. Panels shall have minimum six layers with truss bridge design for higher flexibility& strength. Panels with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning andvisual appearance. Panels shallbe manufactured with vertical standing seam at both sides of the panel. Panels shall be fixed on Purlin with snap on connectors with double tooth griplock lockingmechanism andwill besecured on MS structure (will be paid Separately) with 3 One Numbers self-drilling screws & trapezoid SS fasteners holding the base of the standing seam offering best stability having a pull-out load of min. 7000N (7KN) tested as per ISO 6892:1998 and IS 1608: 2005, as per design requirement. Panels must satisfyDart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheets which have been exposed to UV for a min. of 500 Hours as per ASTM G 155. Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. U value shall not be more than 1.6 W/m2K as per EN ISO 10077-2:2018. Panel shall be with additional End cap/Aluminium U/F profile/ Glazing Bar for ends as required. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing & direction of the engineering in charge. Colour: As per Approval. Approved Make: FLUX byDPIDaylighting or approved equivalent The 12mm thick panels shall be used for a roofing height of upto 15 mtrs. | sqm | ₹ 3,971 |
| 51.188 | Supply and Installation of Dpi Flux translucent roof with standing seam multicell polycarbonate panel system. The system with complete assembly of co extruded UV protected multicell panels incorporated intoa completesystem. Co-extruded UV protected polycarbonate panel system of min 16 mm thick of 1200mm (min.) width with angular daylighting concept. Panels shall have minimum seven layers in a truss bridge design for higher flexibility & strength. Panels with opaque and translucent clear combination as per required lux level and design requirements with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels shall have an additional IR Blocking features for enhance thermal comfort. Panels shall be manufactured with vertical standing seam at both sides of the panel. Panels shall be fixed on Purlin with snap on connectors with double tooth grip lock locking mechanism and will be secured on MS structure (will be paid Separately) with 3 One Numbers self- drilling screws & trapezoid SS fasteners holding the base of the standing seam offering best stability having a pull-out load of min. 7000N (7KN) tested as per ISO 6892:1998 and IS 1608: 2005,as perdesign requirement. Panels must satisfyDart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheets which have been exposed to UV for a min. of 500 Hours as per ASTM G 155. Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. U value shall not bemore than1.9 W/m2Kas per EN ISO 10077-2:2018. Panel shall be with additional End cap/Aluminium U/F profile/ Glazing Bar for ends as required. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to completethe entirepanel installation as perdrawing &direction ofthe engineerin charge. Colour: As per approval The 16mm thick panels shall be used for a roofing height of upto 15 mtrs. | sqm | ₹ 5,025 |
| 51.189 | Supply and Installation of Dpi Flux translucent roof with standing seam multicell polycarbonate panel system. The system with complete assembly of co extruded UV protected multicell panels incorporated intoa completesystem. Co-extruded UV protected polycarbonate panel system of min 18 mm thick of 1200mm (min.) width with angular daylighting concept. Panels shall have minimum seven layers in a truss bridge design for higher flexibility & strength. Panels with opaque and translucent clear combination as per required lux level and design requirements with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels shall have an additional IR Blocking features for enhance thermal comfort. Panels shall be manufactured with vertical standing seam at both sides of the panel. Panels shall be fixed on Purlin with snap on connectors with double tooth grip lock locking mechanism and will be secured on MS structure (will be paid Separately) with a continuous aluminium I Beam holding the base of the standing seam along the length of the panel & fixed with purlin withself-drillinghex headscrews offeringbest stabilitywith apull-out loadof min. 21000N (21KN) tested as per ISO 6892:1998 and IS 1608: 2005., as per design requirement. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheets which have been exposed to UV for a min. of 500 Hours as per ASTM G 155. Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. U value shall not be more than 1.9 W/m2K as per EN ISO 10077-2:2018. Panel shall be with additional End cap/Aluminium U/F profile/ Glazing Bar for ends as required. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing & direction of the engineer in charge. Colour: As per approval. The 18mm thick panels shall be used for a roofing height of upto 25 mtrs | sqm | ₹ 5,444 |
| 51.190 | Supply and Installation of Dpi Flux translucent roof with standing seam multicell polycarbonate panel system. The system with complete assembly of co extruded UV protected multicell panels incorporated intoa completesystem. Co-extruded UV protected polycarbonate panel system of min 22 mm thick of 1200mm (min.) width with angular daylighting concept. Panels shall have minimum seven layers in a truss bridge design for higher flexibility & strength. Panels with opaque and translucent clear combination as per required lux level and design requirements with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels shall have an additional IR Blocking features for enhance thermal comfort. Panels shall be manufactured with vertical standing seam at both sides of the panel. Panels shall be fixed on Purlin with snap on connectors with double tooth grip lock locking mechanism and will be secured on MS structure (will be paid Separately) with a continuous aluminium I Beam holding the base of the standing seam along the length of the panel & fixed with purlin withself-drillinghex headscrews offeringbest stabilitywith apull-out loadof min. 21000N (21KN) tested as per ISO 6892:1998 and IS 1608: 2005., as per design requirement. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheets which have been exposed to UV for a min. of 500 Hours as per ASTM G 155. Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. U value shall not be more than 1.9 W/m2K as per EN ISO 10077-2:2018. Panel shall be with additional End cap/Aluminium U/F profile/ Glazing Bar for ends as required. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing & direction of the engineer in charge. Colour: As per approval The 22mm thick panels shall be used for a roofing height of upto 55 mtrs. | sqm | ₹ 6,119 |
| 51.191 | Providing and applying two coats of Hues Surface Coatings Clear Coat (Stone-X) with silicon technology on stones, clay tiles, bricks, facades,sand stone,plastered,texture finished interior or exterior surfaces.(It is tested with standand test method One NumberIS15489:2004 & Low VOC as per ASTM D2369/ISO 11890-1 and water vapour permeability as per ASTM D-1653/ISO 7783).Surface preparation includes cleaning and scrubbing with brush,soap and water to remove all dust, fungus,cement, paints etc,washing with water all complete.The coating thickness and the methodology of application shall strictly as per manufacturer's specifitions and as approved byengineer in charge.The contractor shall give guarantee for the performance of coating for water repellencyandalso thedurabitityof coating, all completeas perdirection ofEngineer -in- incharge. | sqm | ₹ 282 |
| 51.192 | Providing and Fixing Processed Stone Cladding on wall surface/ plywood surface. RCC pardi/ Wall and all type of Interior, Exterior Compound wall and Gate etc. of cladding processed stone with material of Processed clay, Wooden chips, Silica sand, Cement, GFRC admixtures, Colour pigments, Fiber up to thick of 230 mm/ 25 mm including scaffolding, fixing of screw, etc. (As directed by Engineer in Charge) | sqm | ₹ 8,598 |
| 51.193 | FRP Beam Crash Barrier -- Type - A, W: FRP Beam Crash Barrier (Providing and erecting a W "FRP beam crash barrier comprising of 3 mm thick corrugated sheet FRP beamrail, 70cm aboveroad/ground level,fixed onISMC series channel verticalpost, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:14856 (2000) and IS:18319 (2015), FRP beam rail to befixed onthe verticalpost with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 810)" As directed by Engineer incharge. | rmt | ₹ 3,377 |
| 51.194 | FRP Beam Crash Barrier -- Type - B, THRIE: FRP Beam Crash Barrier (Providing and erecting aThrie"FRP beamcrashbarriercomprising of3 mmthick corrugated sheet FRP beamrail, 85cm aboveroad/ground level,fixed onISMC series channel verticalpost, 150 x 75 x 5 mm spaced 2 m centre to centre, 2 m high with 1.15 m below ground level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:14856 (2000) and IS:18319 (2015), FRP beam rail to befixed onthe verticalpost with a space of channel section 150 x 75 x 5 mm, 546 mm long complete as per clause 810)" As directed by Engineer incharge. | rmt | ₹ 4,867 |
| 51.228.a | FL-100 for the catchment up to 110 sq.m. system size 90 mm diameter inlet, 63 mm diameter clean water outlet, 90 mm diameter drain outlet (filterain,tee,door bend, valve 63mm) | nos | ₹ 7,203 |
| 51.228.b | FL-150 for the catchment up to 150 sq.m. system size 90 mm diameter inlet, 75 mm diameter clean water outlet, 90 mm diameter drain outlet (filterain,tee,door bend, valve 63mm) | nos | ₹ 9,746 |
| 51.228.c | FL-200 for the catchment up to 225 sq.m. system size 110 mm diameter inlet, 75 mm diameter clean water outlet, 90 mm diameter drain outlet (filterain,tee,door bend, valve 75mm) | nos | ₹ 10,381 |
| 51.228.d | FL-300 for the catchment up to 350 sq.m. system size 110 mm diameter inlet, 90 mm diameter clean water outlet, 90 mm diameter drain outlet (filterain,tee,door bend, valve 90mm) | nos | ₹ 14,195 |
| 51.228.e | FL-500 for the catchment up to 500 sq.m. system size 110 mm diameter inlet, 90 mm diameter clean water outlet, 110 mm diameter drain outlet (filterain,tee,door bend, valve 90mm) | nos | ₹ 20,275 |
| 51.229 | To carry out linear Drone survey agencies will use fully autonomous professional survey grade drone and in post process for aerial triangulation required ground control points and benchmarks will be collected by using survey grade dual frequency DGPS-PPK system. After post processing agency will deliver following final output. 1.Geotagged images in JPG format with resolution of 4-5cm/pixel with 70% overlap 2. GCP values in.CSV format. 3. 3D point cloud cover in.las format. 4. digital surface model (DSM) in.tiff format. 5. 2D orthorectified images in.t iff format with 5 cm resolution which gives capability to capture detailed features. | Running One Kilometre | ₹ 8,500 |
| 51.229a | To carry out polygon Drone survey agencies will use fully autonomous professional survey grade drone and in post process for aerial triangulation required ground control points andbenchmarks willbecollected byusing surveygrade dualfrequencyDGPS-PPK system. After post processing agency will deliver following final output. 1.Geotagged images in JPG format with resolution of 4-5cm/pixel with 70% overlap 2. GCP values in.CSV format. 3. 3D point cloud cover in.las format. 4. digital surface model (DSM) in.tiff format. 5. 2D orthorectified images in.t iff format with 5 cm resolution which gives capability to capture detailed features. | Square One Kilometre | ₹ 22,500 |
| 51.230 | Scanning, Digitisation and Geo-referencing of cadastral /revenue maps and interpretation of all existing features like building, water bodies, rivers, agricultural field etc to generate base map. Creation of GIS platform by using orthorectified image and revenue data by Linking of textual data(7/12) which special data( Vector digitised maps). All will helps to analyse and identify all affected properties. | Square One Kilometre | ₹ 4,000 |
| 51.231 | FALSE CEILING SYSTEM GI METAL BIOGUARD CLIP IN PLAIN TILE WITH CARRIER SYSTEM 600 X 600MM Providing & Fixing horizontal level suspended ceiling comprising of GI Bioguard Clip-in Plain Tile 600x600mm (Nominal Size) tiles of 120 gsm galvanized steel as per IS 277 (2003) suitable for architectural finishes in 0.5mm thickness as per in IS:513 (1994) in Global white color with concealed suspension system having a bevelled edge of 3x3mm and height of 33mm on one side and 18mm on the other side. Tiles shall be flattened by precision leveller to minimize sagto less than 1/400mm.The tiles shall havedouble round pip of ɸ 2mm and ɸ 6mm for secure engagement and levelling respectively, along with swing down feature and special tabs to allow removal of tile to enable plenum access. The coated surface of the tile shall exhibit anti-microbial properties (eradication and inhibition of growth) and shall achieve up to 99.99% reduction in bacterial activity as per ISO22196:2011. The tile shall be electrostatically polyester powder coated using RoHS compliant powder having coating thickness ranging from 60-80 microns. The powder coating shall pass Salt Spray Test for 750 Hours as per ASTM B117, QUV –A Test for 1000hours as per ASTM G-154 – (Cycle – 1)and Humiditytest for1000hours asper DIN 50017. The powder coating shall have an adhesion of GT0 as per EN ISO 2409. The shade variation across batches shall be delta E<1 using Excite/BYK Gardner instrument and gloss level of 25±5% at 60˚ as per ASTM D523. The tile shall have scratch, mar & abrasive resistance properties. The tile shall have a Light Reflectance of ≥ 63% in accordance to ASTM 1477-98 and Fire Performance of class 0/1as perBS 476Part 6& 7 in module size of 600x600mm. SUSPENSION & INSTALLATION: Shall comprise of 3000mm long ‘C’ channels of 38H x 12W mm and 1mm thick spaced at 1200mm centre to centre securely fixed to the structural soffit using threaded rod (Approved make/Third Party Supply) connecting to C- channel hanger of 109x18.5x16.5mm at 1200mm C/C and anchor fastener (Approved make/Third Party Supply). The last hanger at the end of each C-channel shall not be greater than 600mm from the adjacent wall. Use a C-channel connector of 99.5x35x 9mm for splicing together two pieces of C-channels. 4000mm Clip-in bar of 16W x 40H mm and 0.6mm thick made of galvanized steel of 140gsm as IS 277 (2003) and shall be | sqm | ₹ 2,457 |
| 51.232 | ACOUSTICAL WALL PANELLING – FABRIC WRAPPED OF SIZE: 600X600/1200X25MM Providing and Fixing of Acoustical Wall Panel with square edges made of fibre glass substrate 25mm thick, wrapped on the front side with an acoustically transparent fabric as per the approved shade (Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell). The panel shall be classified for Fire Class A, as per ASTM E- 84. The Acoustical Wall Panel shall be of sizes 600x600mm (Nominal) or 600x1200mm (Nominal) and shall achieve an NRC of 0.85 (Average value of Absorption Co-efficient readings takenat 250Hz,500Hz,1000Hzand2000Hz)with 50mmairgap asper ASTM C423 to be fixed to wall on a framework of wooden battens and using Wall panel Impalers (supplied by the manufacturer) or by using construction adhesives (as per the instructions laid down by the manufacturer). The fibre glass substrate shall have a recycle content of 85%. Installation:An appropriate vapour barrier (by others) shall be applied/installed on the vertical surface before the installation to properly seal against entry of any moisture. Vapour barrier (by others) shall be installed as per Manufacturer’s recommendation. Install wooden batten grid (providedbyothers)of section 50x50mm oras approvedbythe Architect on the solid wall/partition to provide level and plumb surface. The Impalers shall be fixed to the battens using self-tapping screws, 3 nos. in case of 600x600mm and 4 nos. in case of600x1200mm. Silicabased construction adhesive (byothers) tobe dabbedon to the projecting elements (spikes)of theImpalers. WallPanels shallbe pierced through the spikes of the Impalers ensuring the line and level of the panels are maintained | sqm | ₹ 6,645 |
| 51.233 | CHANNELLED WALL PANELLING OF SIZE: 192X2400X15MM Providing and Fixing Channelled perforated panels of width 192mm, thickness of 15mm and length 2400 mm, made of a Moisture resistant fibre board substrate with a laminated facing as per the approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut, Interior White, Alumina Pearl) and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the reverse surface has a “Helmholtz” fluted perforation with consecutive 3mm wide groove followed by13mm or 21mm of visible pane (G-13/ G-21). The edges of the panel shall be “tongue-and- grooved” to fix special clips for installation and seamless visual. The back of the perforated panel shall have sound absorbing non-woven Soundtex acoustical fleece hot pressed to achieve NRC of 0.5. for G-21 and 0.6 for G-13. (Average value of Absorption Co-efficient readings takenat 250Hz, 500Hz, 1000Hz and 2000 Hz)as perASTM C423 and Humidity Resistance (RH) of 70% with camber limit less than 1mm/1000mm and bow less than 1mm/300mOne Metric Tonnehe panels shall be mounted on special aluminiumsplines (keel)using insideclips providedbyManufacturerand approvedbythe Architect/ Engineer-in-Charge. (cid:10) | sqm | ₹ 5,001 |
| 51.234 | Providing & Fixing Of Classic Axiom Perimeter Trim with 19mm face for perimeter solution of acoustical ceiling using appropriate Accessories Classic Vector Axiom (AX4VESTRI/ AX4VECURI xx) to offer perimeter solution with acoustical ceiling system. Classic Vector Axiom (AX2STR42I/ AX2CUR42Ixx) is made of extruded aluminum of O/L dimension of 19.3 x 100 x 3000mm. The inverted F- Shape section provides 2 flanges and 19mm face for resting of tiles. Classsic Axiom must be powder coated in Global White. Profile to have engineered design boss for fitment of Tee bar connector, Splice plate Corner connector & hanger clips. Classic Axiom ( AX4VECURI xx) can be curvered to a minumum radius of 600mm Axiom Splice Plate (AX4SPLICEI/AXSPLICEI): Formed to fit into special boss in the Axiom and locked in place with factory-installed screws. These Steel splice plates (AX4SPLICEI) are used to align and secure all joints between sections of Axiom trims. Corners are to be formed by mitering the end of axiom and splice plate (AXSPLICE) to be bent at right angle for connecting the end pieces. Axiom Tee-Bar Connection Clip (AXTBCI): Commercial quality G.I formed to fit into special boss of trim and locked in place by factory-installed screws and attached to (XL-24 / XL-15/Silhouette) suspension system members. T-Bar connection clips are used to attach the Axiom to the supporting Suspension system members. One clip is requiredat eachlocation wherethe grid system intersects the Axiom trim. Hanging Grid clips (AXHGCI): Axioms to be hung independently to the structural soffit by engaging the Hanging Grid Clip into the boss of the Axiom trim channel and securing it tostructural soffit Suspension.INSTALLATION: Hangthe sections of Axiom Trim onto the grid system byengaging thetop earof theconnection clipunder theboss of the channel trim. Slide the lower leg downward to engage the lower boss on the trim and secure by tightening the locking screw. Complete the installation of all channel trims sections. Install and secure the splice plates, corner pieces, and alignment plate’s etc. Make adjustments as necessary to properly align the complete installation. | rmt | ₹ 1,229 |
| 51.235 | Supply, fixing and installation of 4mm thick Aluminium Composite Panel (ACP) of approved colour for external cladding in combination of solid and metallic colours, including all necessary Framework, support and complete weather sealing as per architectural drawing. The Aluminium Composite Panel (ACP) should be made out of thermoplastic core of low-density polyethylene LDPE (100% virgin mix), sandwiched between two aluminium sheets of ALLOY GRADE- 5000 series, each not less than 0.50 mm thick, total thickness of aluminium composite panels not to be less than 4 mm, the exposed surface thereof shall have Stove lacquered finishing coat not less than (26 + - 2) micron (containing minimum 70% kynar 500 based PVDF) of colour and shade as per architectural design. The inside surface (facing the building exterior surface)shall have polyster based powder coating not less than 25 Micron with protective peel-off foil on the exterior face (peel off film will in no case leave any adhesive mark over the composite panel surface after it is peeled off). The supporting framework shall be made out of 50 mm X25mm X 3mm thick Aluminium section to be spaced horizontally and vertically for fixing of panel of size 900 mm X 1200 mm and fixed to the building structure as per design through 50mm X50mm X5 mm MS angle clamps prefixed to masonry or slab, columns with Hilti make anchor fastener screws. The fixing of panel to be done with the help of VHB tapes and screws and all the sealingof joints to bedone withweather sealent Silicon as directed by Engineer-in-charge. (Prior permission of S.E. is necessary before inclusion of this item in estimate) | sqm | ₹ 3,347 |
| 51.236 | Supplying and fixing of 6mm thick Exterior Compact Laminate or High Pressure Laminate of approved colour by approving authority with UV resistant Decorative colour paper on both side typically made out of multiple layers of craft papers and then impregnated with thermosetting phenolic resins, on top of it melamine treated barrier paper and decorative paper and wear layer on both the sides saturated with melamine resins and then covered with UV resistant acrylic resin layer which makes it extremely durable and weather resistant compressed together on extremely high pressure and hardened with electron beam curing to get the total desired thickness of 6mm matching European standard specification as per EN 438 -part 6, protected with 60 Micron protective peel-off film on both side which in no case leave any adhesive mark over the panel surface after it is peeled off. Fixing of the same to be done on a supporting frame of 50 mm X 5 mm X 3 mm powder coated aluminium box section to be spaced horizontally and vertically in 600mm X 600mm grid and fixed to building structure as per design through 50mmX50mmX mm 5 mm MS angle bracket prefixed to masonry slab or columns with Hilti make anchor fastener along with all related hardware and fixtures. The panel should then be fixed on the Aluminium section with the help of pure polyester exterior grade colour coating rivets as per architectural drawings or as directed by Engineer-in-charge. Each panel should be riveted on substructure maintaining a gap of 6mm on all the sides between each Panel for Air circulation and expansion and contraction as per installation specifications provided by the manufacturer. The cost shall include all expenses related to storage, material handling, lifting, freight, labour, scaffolding etc as directed by Engineer-in-charge. (Prior permission of S.E. is necessary before inclusion of this item in estimate) | sqm | ₹ 5,841 |
| 51.237 | Providing and Laying of 2 or more sets (6 Nos. each set) Dual Ribs Pattern Rumble Markings on roads with vehicular speeds of more than 50 Km/hr laid as per the spacing recommended for each set under Table 11.1 and Fig. 11.2 of IRC 35:2015 using Plastirib 2K, or equivalent 2 component cold plastic profiled material. Each Dual Rib pattern rumble marking shall have width of 500 mm. Each dual rib pattern rumble marking shall have 2 ribs each of Width of 60 mm and height 20 mm. Gap between two ribs shall be 300 mm.Each rumblemarkingshallbemadecompletewithdroponSoildPlusreflective glass beads @ 300 gm / One Square Metre spread throughout the surface of marking. The finished surface to be levelled, uniform and free from streaks and holes, including surface cleaning and cost of all materials etc. complete. as directed by Engineer-in-charge. | sqm | ₹ 4,586 |
Make the estimate with these rates. BESTimate fills the description, unit and rate when you pick the item code — Measurement, Abstract and Summary in Excel.Try BESTimate →
Source: State Schedule of Rates 2022-23, Public Works Department, Government of Maharashtra — completed rates excluding GST. Rates are shown as published; check the official book and its correction slips before you submit an estimate. BESTimate is not issued by or affiliated with this department.
Need the full estimate, not just one item?
BESTimate makes the whole government-format estimate — Measurement, Abstract and Summary in Excel — with BMC, PWD, CPWD, MJP and CIDCO rates built in. Launching 26 November 2026 · first 99 to pre-register get 50% off for 6 months.
Made free with BESTimate by F K Consultant · estimate.fkconsultant.com/calculators · approximate figures — check against your drawings and local rates.